Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
8 shows the wallbox mounting dimensions for the single and double style Mio Modero. AMX recommends mounting the Mio Modero in a standard one-gang wallbox, a conduit box per NEC specs section 370, with a minimum internal clearance of 2-5/8" x 1-3/4" x 1-5/8" (HWD), but it is possible to mount the Mio Modero to a podium without a wallbox. 2.250 [57.2 MM] [83.4 MM] 3.282 [50.8 MM] 2.000 FIG. 8 Mio Modero Single Style mounting dimensions 2.250 [57.2 MM] [83.4 MM] 3.282 [50.8 MM] 2.000 FIG. 9 Mio Modero Double Style mounting dimensions Wallbox Mounting 1. Use the cutout dimension for the wallbox to cutout the install surface for the Mio Modero. 2. Confirm that the terminal end of the AxLink cable is disconnected, and not receiving power. 3. If the faceplate is connected to the mounting frame, place a flathead screwdriver in the notch at the bottom right of the Mio Modero, and pry the faceplate from the mounting frame. 4. Connect the AxLink power supply. The connector passes through the center of the mounting frame and connects to the board. The connection is illustrated in FIG. 2. 5. Place the mounting frame on the wallbox; align the screw holes with the mounting holes and fasten the mounting frame to the wallbox using the screws supplied. Mio Modero Device Family Installation Do not overtighten the screws when mounting the mounting frame. The device should be flush with mounting surface. 6. Attach the faceplate to the mounting frame first at the top and swing it to the bottom. See FIG. 10. FIG. 10 Attaching the faceplate to the mounting frame Podium Mounting 1. Use the cutout dimension shown in either FIG. 8 or FIG. 9 to cutout the mounting frame install surface for the Mio Modero. 2. Confirm that the terminal end of the AxLink cable is disconnected, and not receiving power. 3. If the faceplate is connected to the mounting frame, place a flathead screwdriver in the notch at the bottom right of the Mio Modero, and pry the faceplate from the mounting frame. 4. Connect the AxLink power supply. The connector passes through the center of the mounting frame and connects to the board. The connection is illustrated in FIG. 2. 5. With the mounting frame resting in the cutout area, drill the mounting holes into the flat surface. Do not overtighten the screws when mounting the mounting frame. The device should be flush with mounting surface. 6. Attach the faceplate to the mounting frame first at the top and swing it to the bottom (see FIG. 10). Mio Modero Device Family Installation Accent Frame While the Mio Modero device family does fit into many International wallboxes, it may be necessary to utilize the optional accent frame to completely cover the wallbox. To install the Mio Modero with the optional accent frame: 1. Use the cutout dimension for the wallbox to cut out the install surface for the Mio Modero. 2. Place the accent frame on the wallbox; align the screw holes with the mounting holes on the wallplate. Fasten the wallplate to the wallbox. Based on the extensive number of international wallboxes it is not pragmatic to ship every possible screw that could be used. Please use the screws appropriate for your specific wallbox. Do not overtighten the screws when mounting the mounting frame. The device should be flush with mounting surface. 3. Confirm that the terminal end of the AxLink cable is disconnected, and not receiving power. 4. If the faceplate is connected to the mounting frame place a flathead screwdriver in the notch at the bottom right of the Mio Modero IR, and pry the faceplate from the mounting frame. 5. Connect the AxLink power supply. The connector passes through the center of the mounting frame and connects to the board. The connection is illustrated in FIG. 2. 6. Place the mounting frame on the accent frame; align the screw holes with the mounting holes and fasten the mounting frame to the wallplate. The Accent Frame is shipped with two #6-32 x .187 long flat head screws (80-131); these are used to attach the Mio panel to the accent frames. 7. Snap the faceplate to the mounting frame. Mio Modero Device Family Mio Modero IR Mio Modero IR The Mio Modero IR (FIG. 11) is a remote IR receiver for use with NetLinx® Central Controllers and operates via the AxLink bus to remotely control devices. .. The Mio Modero IR is in a wall panel that fits into the US-style single-gang enclosure and most International single-gang enclosures. .. The Mio Modero IR works with AMX 38 kHz and 455 kHz IR transmitters. Mounting Frame Faceplate IR Cover FIG. 11 Mio Modero IR receiver Mio Modero IR Specifications Power: 12 vDC, 15 mA Receive Frequencies: 38 and 455 kHz Range: 38KHz: • Transmitter at 38Hz = max of 95 feet line of sight • Transmitter at 38Hz and at 50° horizontal angle from center = 55 feet • Transmitter at 38Hz and at 30° vertical angle from center = 65 feet 455KHz: • Transmitter at 455Hz = max of 58 feet line of sight • Transmitter at 455Hz and at 45° horizontal angle from center = 31 feet • Transmitter at 45...