Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
There is no need to prepare a separate power source as the power to the studio adapter will be supplied by RMHP790DU/ RM-HP790DE. Equipped with HD/SD SDI connector The unit can distribute and output (2 outputs) the input SDI signals from the SDI input connector. It can be connected to SDI switcher, monitor or other VTR equipment. The camera can be remotely controlled The camera can be remotely controlled by serial communication. You can also control the camera by connecting the optional remote control panel RM-LP25U. External synchronization of HD studio system is possible External synchronization of SD reference sync signal or (VBS or BB), HD tri-level reference sync signal for HD studio system is possible. H phase and SC phase (SD signal) can be adjusted on the front panel. Precautions for Proper Use . To prolong the service life of the RM-HP790DU/RMHP790DE, do not use it or store it in the following places. . A place subject to extremely high or low temperatures. . A place subject to excessive vibration. . A place subject to excessive dust. . A place subject to high humidity. . A place near to a strong source of noise. . Do not apply strong vibrations or impact to the RMHP790DU/ RM-HP790DE during installation or transportation. . If the supply voltage is too high or low, the service life of the RM-HP790DU/RM-HP790DE may be reduced or it may not be able to provide an optimum performance. . Do not connect or disconnect the camera cable connector while the RM-HP790DU/RM-HP790DE is ON. . After turning the RM-HP790DU/RM-HP790DE OFF, wait at least 10 seconds before turning it ON again. . Noise may interfere with the video when the RMHP790DU/ RM-HP790DE is installed near a source of strong magnetism, such as a radio or TV transmitting antenna, power transformer or motor. . While the values set by using the menus are retained in the memory even after the unit is turned off, those set using the front panel switches and controls are retained for about 10 days only and then the factory-set defaults are reset. . As the LCD contrast is reduced at low temperatures, it should be re-adjusted before use in such conditions. (APage 26 [CONTRAST]) . When a transceiver or cellular phone is used near to a RM-HP790DU/RM-HP790DE or to a camera connected to it, noise may interfere with the video. However, this is not a malfunction. . When an intercom is used, radio interference may occasionally affect any system that is connected to the RMHP790DU/ RM-HP790DE. . In such a case the INTERCOM G (GND) terminal provided to the RM-HP790DU/RM-HP790DE should be grounded. . In a multiple camera setup, if the adjustments made to the different cameras deviate significantly, the cameras may not be able to function satisfactorily. Be sure to adjust the cameras accordingly before using them with the RMHP790DU/ RM-HP790DE. . Use camera cables with standard lengths, as specified. Otherwise, the camera cable compensation may not be able to work efficiently. . RM-HP790DU/RM-HP790DE can be connected to the following equipment: . GY-HM790 series (HD Memory Card Camera Recorder) . KA-M790G (Multicore Remote Adapter) . KA-790G (Studio Adapter) . VF-HP790G (Studio Viewfinder) Functions not available on the camera cannot be controlled from this unit. (A Page 29 [Operable Camera Features]) . If the RM-HP790DU/RM-HP790DE is rack-mounted, be sure to insert ventilated panels above and below it in order to improve ventilation, Do not stack two RM-HP790DU/RMHP790DE units or place any object on top of a RMHP790DU/ RM-HP790DE unit. In addition, make sure to keep surrounding temperature of this unit below 40f during use. . To save power consumption, turn the RM-HP790DU/RMHP790DE OFF when it is not in use. Introduction Names of Parts Front panel ABCDEF GH IJKM O QRST U V TALLY CALL FULL AUTO BARS F2 F1 F4 MENU SHUTTER MENU/SHUTTER GAIN WHITE MASTER BLACK IRIS PUSH-ON DOWN UP VARIABLE PUSH-ON STEP PAINT R AUTO B HIGH W.BAL POWER AUTO MANU B A CLOSE OPEN PRESETLOW MID DOWN UP F3 INTERCOM LEVEL REMOTE CONTROL UNIT RM-HP790 GAIN SHUTTER LNP A Intercom connector Connect the intercom headset to this connector. (APage 14 [Intercom]) B [INTERCOM LEVEL] control Use this knob to adjust the intercom earphone volume. C [TALLY] lamp This lamp lights when a signal is input to the [TALLY] terminals B on the rear panel. It lights in red when a tally signal is input to the [TALLY PGM] terminal on the rear panel or in green when a tally signal is input to the [TALLY PVW] terminal. Memo : . The button lamps will light up and blink as below. . During CALL : [CALL] button blinks in red . TALLY PGM : [TALLY] lamp lights up in red . TALLY PVW : [TALLY] lamp lights up in green D [CALL] button and indicator light*1 The camera operator can also be called without using the intercom. When this button is pressed once, the light in it lights up and the tally lamp on the camera blinks to inform the camera operator of a call. Pressing this button again turns off both the button light and tally ...
Otros modelos de este manual:Control remoto - RM-HP790DU, RM-HP790DE RM-HP790DU (1.74 mb)