Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
This is because we test all our steam mops 100% before you buy them, so you get a quality Shark® Light & Easy™ Steam Mop. ef fig. 1 fig. 2 a Upper Handle Tube with Backsaver ASSEMBLY 3 Insert the assembled handle piece IMPORTANT: Never use the Light & benefit 1 Remove all the parts from the into the steam mop base. Push the Easy™ Steam Mop without attaching package. Verify all the listed parts tube base together until you hear a a micro-fiber cleaning pad to avoid b Lower Tube are included. click. (fig. 2) damage to your floor and mop. c Steam Mop Base 2 Slide the Upper Handle Tube (the d 2 All-Purpose Cleaning Pads tube with the handle) into the Lower e Filling Flask Tube (the short tube). Push the two extension tubes together until you f Funnel hear them click into place. (fig. 1) S3250CW_11_IB_ENG_100913.indd 2-3 10-09-13 10:57 AM 4 TOLL FREE: 1 800 418 0934 5English ATTACHING THE MICRO-FIBER PAD 1 Place the micro-fiber cleaning pad on the floor with the quick fastener strips facing up. Place the Light & Easy™ Steam Mop on the top of the pad to attach. (fig. 1) IMPORTANT: Only add water to the tank. Chemicals or cleaning solutions may be unsafe or cause damage. Getting Started - cont’d FILLING THE WATER TANK IMPORTANT: Unplug the Light & Easy™ Steam Mop before filling the water tank with water. (fig. 2) 1 Remove the water tank cap by turning it counter-clockwise to the unlocked position. (fig. 3) 2 A filling flask and funnel are included with your Light & Easy™ Steam Mop to make filling the water tank easy. Fill the flask with water and use the funnel to pour it into the tank. Keep the water level under the MAX FILL line. (fig. 3) 3 Replace the water tank cap and turn it clockwise to the locked position. Replacement micro-fiber pads are available at or by calling 1-800-418-0934. fig. 1 fig. 3 fig. 2 Your micro-fiber cleaning pads should be replaced every 3 months to maximize cleaning performance. 4 TOLL FREE: 1 800 418 0934 5English ATTACHING THE MICRO-FIBER PAD 1 Place the micro-fiber cleaning pad on the floor with the quick fastener strips facing up. Place the Light & Easy™ Steam Mop on the top of the pad to attach. (fig. 1) IMPORTANT: Only add water to the tank. Chemicals or cleaning solutions may be unsafe or cause damage. Getting Started - cont’d FILLING THE WATER TANK IMPORTANT: Unplug the Light & Easy™ Steam Mop before filling the water tank with water. (fig. 2) 1 Remove the water tank cap by turning it counter-clockwise to the unlocked position. (fig. 3) 2 A filling flask and funnel are included with your Light & Easy™ Steam Mop to make filling the water tank easy. Fill the flask with water and use the funnel to pour it into the tank. Keep the water level under the MAX FILL line. (fig. 3) 3 Replace the water tank cap and turn it clockwise to the locked position. Replacement micro-fiber pads are available at or by calling 1-800-418-0934. fig. 1 fig. 3 fig. 2 Your micro-fiber cleaning pads should be replaced every 3 months to maximize cleaning performance. S3250CW_11_IB_ENG_100913.indd 4-5 10-09-13 10:57 AM Using Your Light & Easy™ Steam Mop IMPORTANT: Your steam mop needs water to make steam! Never use your steam mop without water in the tank. Sweep or vacuum your floors prior to cleaning with your Light & Easy™ Steam Mop. Visit for other great quick cleaning products to complement your Light & Easy™ Steam Mop. When you use your steam mop for the first time or if you have not used the unit in awhile, it may take a minute or two for the water to travel through the pump and into the heater to create steam. Get it started by pumping the handle a few times. If you have waited a few minutes and you still do not see any steam, reference the troubleshooting section on page 11. fig. 1 fig. 4 fig. 5 fig. 2 fig. 3 If your Light & Easy™ Steam Mop stops steaming, it could be out of water. Unplug the power cord from the electrical outlet and refill the water tank at anytime. 1 Pull and twist the quick release 2 Wait 30 seconds for the boiler to 3 Mop with a forward and backward cord holder to unwrap the power heat the water. Pump the handle motion to customize steam output cord completely. (fig. 1) Plug into a few times to prime the pump, automatically. (fig. 5) a 120-volt electrical outlet. (fig. 2) activate steam and moisten the The “On” light will turn blue. If the micro-fiber pad. (fig. 4) light does not turn on, reference the troubleshooting section on page 11. (fig. 3) S3250CW_11_IB_ENG_100913.indd 6-7 10-09-13 10:57 AM English Using Your Light & Easy™ Steam Mop - cont’d Care of Your Light & Easy™ Steam Mop 1 2 Clean under furniture and tight areas using the Shark® Backsaver™ locking handle. Press the handle release button and apply slight pressure to bend the handle. The Shark® Backsaver™ joint will lock at a perfect, access-maximizing angle. (fig. 1) Press the release button on the handle again to straighten....