Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
2.0 Safety The Sinclair Super® Stripper is state of the art designed and meets all standard safety requirements. 3.0 Safety Instructions Disconnect the power supply before any maintenance is carried out. Use only recommended blades and make sure the blade is sharp before starting. Maintenance should be undertaken only by qualified personnel. Use only genuine Sinclair parts. Transport Always remove the blade before transporting the machine. CAUTION!!! Always wear ear and eye protectors! CAUTION!!! Using this machine without ear and eye protectors may jeopardize or harm your health. It may harm especially your ears and increase the risk of an accident. * PLEASE READ DETAILED SAFETY INSTRUCTIONS ON COLORED SHEET BEFORE USING MACHINE! 3.1 Introduction This operating manual should be used to receive the maximum benefit from your Super® Stripper. Following these instructions will both extend the life of your machine and reduce repair costs. Please make sure any user of the machine is familiar with these instructions before work begins. 3.2 Danger while working with the machine The Super® Stripper is designed to the highest technical standards. Incorrect use can be dangerous! Use this machine only: - As instructed in this operating manual. - With the machine in perfect working order. Disturbances that could impair safety have to be eliminated at once. 3.3 Restriction of use The Super® Stripper is exclusively for removing bonded floor covering in dry environments. It should not be used for any other purpose. Sinclair Equipment Company cannot be held responsible for any damage or loss caused by incorrect use. Correct use also includes: - To take care of all directions from the operating manual and - The execution of maintenance and service. 4.0 Maintenance The Super® Stripper is virtually maintenance free. The guide shaft castings require lubrication from time to time. (After approx. 1650 sq. feet). Initially the machine is fully’ lubricated and should not require any additional lubrication for the first 5000 square feet. The zirc fittings are located on each side (see diagram). 1) To Grease the gearbox on its right side, remove left wheel and bottom cover. Spin axel/gearbox to expose zirc fitting. (See Diagram 2) Put 2 to 3 pumps to gearbox every 50 to 75 hours. The used grease will flush dirt out of the machine. Replacement lubrication should be a Lithium based chassis type lube (i.e. auto grease gun pack). Diagram 1 Diagram 2 The used grease will flush dirt out of the machine. Replacement lubrication should be a Lithium based chassis type lube (i.e. auto grease gun pack). CAUTION !! Press maximum 3 to 4 times with the grease gun. Never press too much grease into the machine. Otherwise the mechanism will be blocked. Changing the blade Disconnect the power supply and put on the blade protection before changing the blade. Use work gloves for your own safety. -Tip the machine -Put on the blade protection (enclosed in the tool set) Warning! Very sharp blade! You may cause injury without using the blade protection! -Secure the tipped machine from tilting over -Clean and loosen screws of the blade mounting Attention! Set the wrench at a position opposite to the blade to avoid injury. -replace the blade Make sure that the sharp bevel of the blade always shows upwards and the blade is fitting in exactly the position of the old one. Changing the driving wheels Remove the lynch-pins and pull the wheels from the axle. Do not loose the wheel key under any circumstances. 5.0 Use The Super® Stripper removes bonded, flexible floor covering in strips. This procedure corresponds with the customary method of using a hand floor scraper. The stripper works with a steel blade at a very high frequency, minimizing vibration and noise. The Super® Stripper is self propelled. The motor actuates both the blade and the machine movement. The blade drive starts as soon as the machine is switched on. Starting The Super® Stripper is equipped with an operating switch located at the top of the handle. This is a safety switch, which must be held down to engage the Super® Stripper. There is a current limiting protective device which causes a two second delay to full power on start. Before starting work, cut the floor covering into strips of about 30cm (11 inches). You cannot work faster if you cut wider strips. To begin, cut one strip crosswise. Then lift the flooring slightly in order to get the blade underneath it. We recommend to cut the first strip at right angles to the main working direction. By doing so, access to the adjacent strips is made easier. Cut the strips smaller if the floor covering is bonded very securely, e.g. with an epoxy adhesive. The blades are sharpened by the floor pavement. Therefore the blade has to be changed only if it is twisted or becomes worn. The driving wheels are subject to wear. They have to be changed after approximately 16mm (0.6 inch) of the surface has been worn away. Otherwise the working angle of the striki...