Votos - 2, Puntuación media: 4 ( )

Fabricar: Earlex Tamaño del archivo: 223.99 kb Nombre del archivo: Idioma del manual:

The Earlex Steam Cleaning Kit does not require detergents, chemicals or other cleaners. It cleans purely by the action of steam. This action also removes any traces of powder or liquid cleaners previously used. protecT youR home! The heat generated by the boiler unit can mark carpets, soft furnishings, table tops, cabinets etc. To prevent this we recommend placing the unit on a wooden board, tray or other barrier -making sure it will not slip off one side or tilt during use. Dust sheets or newspapers are not suitable heat protectors for delicate surfaces. ImportanT notE Always check the suitability of materials before steam cleaning. Steam is being generated at 100.C. Do not use on any surfaces that cannot stand this temperature e.g. Draylon®, delicate fabrics etc. Always test a small area of the material -preferably a portion that is normally unseen -and allow to dry before starting the full cleaning task. Do not soak materials being cleaned. Only light application of steam is required. cautIoN steaM IS hot! Please be aware that steam is produced at 100.C -so be careful, wear protective clothing and protect your hands with heat resistant gloves or mitts. 2 steaM cleanInG KIT contentS please note: Not all of the accessories shown in this instruction booklet are included in every steam cleaning kit. To check the contents of your steam cleaning kit, please refer to the colour packaging (where supplied), catalogue or store where the unit was purchased. If you are unsure about the contents of your steam cleaning kit, please contact our helpline on 01483 454666. component list Steam Boiler (not shown) SC75 D87 SC125 B44 SC165 ST118 Mains Lead with Plug 3m (not shown) B17 Mains Lead with Plug 2m (not shown) C3P a Floor Cleaner AC254 b Towel for Floor Cleaner AC275 c Window/Tile Cleaner AC258 d Jet Nozzle AC262 e Scraper for Jet Nozzle AC21 f Brush for Jet Nozzle AC25 g Universal Handle AC302 h 3 lengths of Handle AC01 i 3.6m Steam Hose ST94 3.6m Steam Hose (SC75)(not shown) D14 optIonaL accessorIeS (not included in all kits) j Large Plate for wallpaper stripping D39 k Small Steam Plate ST165 l Upholstery Cleaner AC250 m Towel for Upholstery Cleaner AC276 Sink Unblocker Tube (not shown) NRL/.5 Castors (SC165 optional) (not shown) F17 ijcefdgbalmkh assemblInG thE accessorIeS The Universal Handle (AC302) is used in conjunction with the Floor Cleaner, Upholstery Cleaner, Window / Tile Cleaner and Jet Nozzle. Align the outline triangle on the handle with the triangle on the accessory. Push the handle into the accessory and twist so that the solid triangles on the handle and accessory are aligned (see Diagram 1). Over time, you may find that your steam cleaning accessories become awkward to assemble to the universal handle. This is due to the steam reducing the lubrication properties of the ‘O. ring seals. In this event, simply lubricate the ‘O. ring seals as illustrated (Diagram 2) using washing-up liquid or furniture polish. The Long Handle Attachment (AC01) is designed to be used when cleaning floors or hard to reach areas. To assemble, pass hose through each of the long handle sections, in at the small end out at the large end. Screw the hose nut onto the universal handle and push the long handle sections together and onto the taper on the universal handle (see Diagram 3). You can use one, two or three sections of the long handle. Disconnect in reverse order. If you have any difficulty in disconnecting twist the handles apart. diagram 2 Seal Lubrication diagram 1 Assembling Handle diagram 3 Fitting Long Handle Attachment 3 castorS (modeL sc165 optIonal) The castors are packed separately. Turn the boiler upside down and insert the 3 castors. These should be pushed in hard until they stop. Once installed these remain in place permanently. fIllInG sc75 (see Fig.1) Remove elbow filler cap and fill unit to Max. level indicator with clean -preferably hot water. Ensure that the ‘O. ring is seated correctly on the elbow filler cap and place elbow filler cap lugs into filler hole with the tongue pointing to the TWO O’CLOCK position. Turn the elbow filler cap clockwise to the SIX O’CLOCK position so that the tongue locks into place between the two teeth. sc77, sc125 & sc165 (see Fig.2) Remove filler cap and fill unit to Max. level line or indicator with clean -preferably hot water. Replace filler cap. Fig.1 Fig.2 SC75 SC77, SC125, SC165 do not overfill the unit or hot water will be forced up the steam hose. Screw hose onto threaded outlets of boiler and accessory, hand tight is sufficient. do not over tighten but do check for hand tight fit from time to time during use. Connect mains lead from unit to power socket and switch on. It can take approx 20 mins before steam is produced -depending on fill water quantity and temperature. do not leave unattended and keep children & pets out of the room. Just before full steam production a small amount of bubbling and water will occur at the accessory. beware of hot water discharge pr...

Descargar ahora

Introduzca dos números de la imagen: