Fabricar: Avanti
Tamaño del archivo: 191.68 kb
Nombre del archivo:
|
Resumen del manual
Be careful not to tear the bag. 4. Attach the new dust bag onto the bag holder by holding the bag collar and pushing back as illustrated. 5. The dust bag must be completely installed inside of the dust compartment for proper operation. The dust bag should not be caught between the lower edge of the dust cover and the rubber gasket as indicated by the arrow in the illustration. 6. Reinsert the tab located on the end of the dust cover into the groove on the dust compartment and press the cover into place. The dust cover must be completely and correctly installed for proper operation. > CHANGING THE FILTERS A secondary filter protects the motor from dirt. Before installing a new dust bag. check the filter. 8 Accumulated dirt in the dust compartment will collect on this filter and may restrict motor performance When the filter becomes dirty, pull it from the bottom of the dust compartment and clean when finished slide the filter back into place. It should be fully inserted under the plastic rib projections all the way to the rear compartment wall. Put cassette with filter back in vacuum. Model HMU1100 The electrostatic exhaust filter is located in a cassette inside the dust compartment body The purpose of this filter is to remove dust and dirt from the re-circutated air. It is capable of filtering very fine dirt particles This filter cannot be cleaned and should be replaced at least once per year if the cleaner ts used at least one hour per week. Mode! HMU2000 The hepatype exhaust filter is located in a cassette inside the dust compartment body The purpose of this filter is to remove dust and dirt from the re-circulated air. It is capable of filtering very fine dirt particles. This filter cannot be cleaned and should be replaced at least once per year if the cleaner is used at least one hour per week. > TO ADJUST CARPET HEIGHT Your Home Maker Upright Vacuum cleaner is designed with a low to high adjusting rug nozzle. The height of the rug nozzle can be lowered or raised to any carpet pile height. This adjusting feature allows the rug nozzle to float evenly over all carpet pile surfaces. REPLACING THE BELT Before replacing any parts, disconnect the vacuum cleaner from the electrical outlet. To replace the drive belt, place the handle in the low position. Then turn the vacuum cleaner over, exposing the underside. Release the lower plate by sliding the two plate lock buttons that hold the lower plate on. Then remove the lower plate. Turn the unit over, remove the lower plate as described in the preceding section. Remove the top left packing and take out the agitator assembly (just lift out), and remove the worn or broken belt from the agitator pulley and motor drive shaft. Loop the new belt around the motor drive shaft and then loop it around the agitator pulley. Use only a Home Maker type BU3 drive belt. Reinstall the agitator assembly back into the housing grooves. After installing agitator turn it by hand making sure the belt is not twisted and all rotating parts turn freely. Replace the felt packing. Use replacement genuine belts BU3. To Reinstall Lower Plate Hook the front end of lower plate under the three ribs at the front end of the housing. Then, press the 9 lower plate into place and fasten it by sliding the two plate lock buttons /Vore- To msnee maamvm cleaning efficiency, the bsii should be cftecketf regularly to rxske stir? ,r is m jeed conciito,•> Ct'ic-' :o see ■' :f'e bell is stretched, cracked, or ¡f excosstvs slipping is occurring Replace ■■ needed > CLEANING THE NOZZLE The nozzle hose located on the back of the vacuum cleaner carries the dir: from the nozzle to the dust bag If the hose should become clogged: 1 Remove the nozzle hose from the housing and clean the hose of any obstructions Replace the hose back into the housing. Replace the dust bag with new bag. 2 If the clog still exists, place the handle in the upright locked position. While the cleaner is running, disconnect the nozzle hose from where it enters the nozzle. Stretch the hose in and out to remove the clog. 3. If the clog still exists turn the vacuum cleaner "OFF", unplug the power cord and turn the vacuum cleaner over exposing the underside. Remove the lower plate as described in the proceeding section. Remove the nozzle pipe from the housing by pulling it straight out. Inspect the hose and nozzle pipe, and clear them of any obstructions. Reinstall nozzle pipe and lower plate. Reinstall nozzle hose. SERVICE FOR YOUR VACUUM We are proud of our customer service organization and the network of professional service technicians that provide service on your Avanti appliances. With the purchase of your Avanti vacuum, you can have the confidence that if you ever need additional information or assistance, the Avanti Products Customer Service team will be here for you. Just call us toll-free. AVANTI PRODUCTS CUSTOMER SERVICES Product Information 800-323-5029 Whatever your questions are about our products, he...
Otros modelos de este manual:Aspiradoras - HMU1100 (191.68 kb)