Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
When in the upright position, for storage or tool use, the TLR PowerRoller is lifted off the floor surface and held in space. This will also help the TLR PowerRoller dry between uses. The TLR PowerRoller can be washed or replaced as needed. Ready Tools™ Dial The Ready Tools feature allows you to choose between FLOOR CLEANING or cleaning with TOOLS simply by turning the dial. The TOOLS setting allows for above floor cleaning of upholstery, stairs, creases along baseboards and other hard to reach areas. Simply choose the tool that is appropriate for the job, attach it to the flexible hose and you are ready to go. Easy carry handle Located in the back of the machine, the easy carry handle makes it easy to carry the machine. Refer to page 4 for location. Oxy Gen2 PowerTool Your Prodry model may have come with the Oxy Gen2 PowerTool and Oxy Gen2 formula, If not, these items are available for purchase, refer to page 15. The Oxy Gen2 PowerTool is an advanced stain fighting tool. By adding Oxy Gen2 multi-purpose formula to the tool, tough stains such as coffee, juice, cola and red wine are easier to clean up. The tool can store ready to use with the Oxy Gen2 formula in it. WARNING: To reduce the risk of fire,use only BISSELL advanced deep cleaning formula for full size machines in your carpet cleaner.Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void the warranty.Chemical spot cleaners or solvent-based soil removers should not be used.These products may react with the plastic materials used in your deep cleaner causing cracking or pitting. 6 800.237.7691 ug120-4080_7350_908.indd 6 10/14/08 1:25:57 PM Vacuum area with a dry vacuum cleaner before cleaning Before you clean 1. If desired, move furniture to another area if cleaning an entire room. 2. Operation 3. Plan your cleaning route to leave an exit path. It is best to begin cleaning the corner farthest from your exit 4 Fill the clean/solution tank 24' 3' 13HERE5679101211EXITSTART 1. Remove the clean/solution from the base of the machine by pulling up and out from the back. You can also detent the handle and pull the tank straight up if you desire. 2. Unscrew the black cap and red insert. Remove. 3. Fill the tank up to the FILL LINE with hot tap water. 4. Add 3 ounces of formula (Always use genuine BISSELL formulas to maximize cleaning and for the safety of your machine). OR If using a BISSELL 3X Concentrate add 1 ounce of formula. 5. Replace the cap and insert and tighten by turning clockwise. 6. Replace the clean/solution tank back into the machine. Be sure that the cap is seated in the receiver. Carpet cleaning 1. Make sure the ReadyTools Dial is in the FLOOR CLEANING position. 2. Plug the PROdry into the proper outlet and turn the power ON ( I ) using the switch in the back. 3. With your foot, press the gray handle release lever located on the back of the unit. Take care to notice the way the machine floats forward. 4. While pressing the spray trigger make 1 Tip: Thorough vacuuming forward wet pass and another 1 back. Repeat once and move on to the next before carpet cleaning will prevent section of carpet or area rug to be cleaned. early clogging of the lint screen. Take care not to run over loose objects of the edges of area rugs. 800.237.7691 ug120-4080_7350_908.indd 7 10/14/08 1:25:58 PM Operation Empty the dirty water tank 1. When the dirty water tank level reaches the FULL line, when the float trips or when finished carpet cleaning, turn power switch OFF ( O ). 2. Remove dirty water tank by lifting straight up and carry it to the sink or wherever you plan to dump the dirty water. 3. Remove the tethered cap on the rear of the tank. 4. Pour out the dirty water, rinse tank and replace the cap. 5. To continue carpet cleaning refer back to page 7 beginning with "Fill the clean/solution tank." If cleaning is complete, refer to the “Maintenance and care” section on page 11. Pretreating (optional) 1. Pretreating (optional) Pretreating is recommended to improve cleaning effectiveness for heavily soiled carpet in high traffic areas such as entry ways and hallways. Please keep in mind that pretreating will wet the carpet and could impact dry time. To pretreat: A. Using the BISSELL Tough Stain Pre-cleaner, generously spray evenly over soiled area, do not overwet. B. Wait 3-5 minutes before cleaning. C. Clean as normal using your BISSELL PROdry, following the instructions on page 7. Ready Tools™ (cleaning with attachments) Your PROdry carpet cleaner comes equipped with a hose and at least two attachments for cleaning stairs, upholstery, stains and more. Important! If using the machine to clean upholstery, check upholstery tags. 1. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your PROdry. If the tag is coded with “X” or “S” (with a diagonal strike through), or says “Dry Clean Only,” do not proceed. Do not use on velvet or silk. If manufacturer’s tag is missing ...
Otros modelos de este manual:Aspiradoras - PRODRY E600 (669.86 kb)