Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Turn the machine onto its side so the belt access area is facing upward (see illustration). On the bottom of the machine, near the belt access area, is a red retainer plate that holds the black brush arm and brush in place. Using a Phillips head screwdriver remove the screw that holds the red retainer plate in place. Set red retainer plate and Phillips head screw aside (see illustration). Remove the black brush arm that holds the brush in place. Set the black brush arm aside (see illustration). Remove the “toothed” brush belt from the brush then from the red pump pulley. Set the “toothed” brush belt and brush aside. Locate and remove the broken pump belt. 1. 2. 3. 5. 6. 6. 7. 1. 2. 3. 4. 7. 8. Pump Belt Replacement 4. 5. 8. 9. 9. 10. ON OFF Set dial to: Cap Rotor Filter Tip: SmartMix® Bottle may be stored with concentrate ready for your next cleaning job. Make sure dial is set to Water Only CAUTION: PowerSteamerPro® uses water and must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty. Tankin- Tank SmartMix® 2. 3. 3. 4. 5. 6. 7. 8. 9. Reduced Spray Or No Spray. Possible Causes Remedies Bladder may be empty Turn power OFF; refill tank with hot tap water. SmartMix® Bottle may be empty Turn power OFF; clean out lint screen, follow SmartMix instructions on page 6. The Flow Indicator Filter may be clogged Clean Out Filter; follow Steps under Maintenance/Storage on page 12 Tank-in-Tank may not be seated properly Turn power OFF; remove tank and check gasket on tank bottom, reseat tank Pump may have lost prime Turn power OFF; after 1 minute, turn ON and depress Spray trigger. 13. With the unit still on its side, loop one end of the replacement pump belt around the red pump pulley and then the other end around the silver motor shaft (see illustration). Do not twist the replacement pump belt. Re-install the toothed brush belt first onto the red pump pulley and then onto the toothed end of the brush (see Illustration). Re-install the brush into the base of the unit. Place the black brush arm onto the brush and slide black brush arm into base of unit. The black brush arm and brush should slide easily into original position (see illustration). Re-install the red retainer plate and Phillips head screw (see illustration). Using your finger, gently spin the replacement pump belt on the silver motor shaft. If assembled correctly, the replacement pump belt should rotate freely around the silver motor shaft and drive pulley without obstruction. The brush should also rotate freely when the silver motor shaft is turned. Turn the machine right side up and replace the Tank-in-Tank,™ Smart Mix® tank and belt access door (see illustration). Assembly is now complete. If you have any questions, or are having trouble installing your replacement pump belt, please call BISSELL Consumer Services at 1-800-237-7691. 1. 2. 3. 5. 6. 4. 7. 8. 1. 2. 3. 4. 5. 6. 7a 7b To Install The Replacement Pump Belt 1 1 2 2 3 3 WARNING: To reduce the risk of fire, electric shock or injury, unplug appliance from outlet before servicing. Troubleshooting 4 4 5 5 Reduced Spray Or No Spray. Possible Causes Remedies The Pump Belt may be broken Turn the machine OFF and unplug from the outlet. To check if a Pump Belt has broken, you will need a flat head screwdriver. Insert the blade end into the lower slot of the Belt Access door to release the lower snap. If necessary, insert the blade end into the upper slot to release the upper snap. Examine for belt breakage. You should be able to see the Pump Belt looped around the motor shaft. If it is broken or missing, please refer to Part Numbers and Descriptions on page 15 before calling Consumer Services. Complete installation instructions will accompany the replacement belt. PowerSteamer is not picking up solution. Possible Causes Remedies ReadyTools Dial may be at the Set ReadyTools Dial to either FLOOR wrong setting for cleaning job. CLEANING or TOOLS/PRETREAT. Nozzle Window may not be properly attached Make sure the two tabs on the back of the Floor Nozzle Window are inserted through the mating slots in the main housing. Reinstall if necessary. Tank-in-Tank Lid is not properly installed Reinstall lid; refer to page 6. Tank-in-Tank is not properly seated Tank-in-Tank must be firmly seated to function. Remove tank and check gasket on tank bottom; Reseat tank. Poor tool position. Readjust angle; apply more (Handheld attachments only.) downward pressure. Tank-in-Tank has picked up the maximum Empty tank and refill; refer to dirty water page 7. Thank you for selecting a BISSELL product. If you should happen to need assistance during assembly or operations, call 1-800-237-7691. Please do not return this product to the store 1 1 Troubleshooting Continued 1 1 2 2 3 3 4 4 5 5 6 6 Lift Here Insert Screwdriver Blade Here 14. Troubleshooting Continued 1 1 2 2 3 3 4 4 5 5 6 6 Lift Here Insert Screwdriver Blade Here 14. 15. BISSELL Consumer Services For information ...