Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
4. Apply downward pressure on the tool and pull it toward you. The suction will remove the dirt and cleaning solution. Continue until no more dirt can be removed. Note: If using the TurboBrush, move the switch to the “SUCTION” position. This activates the suction to remove the dirt and cleaning solution. Move the switch back to the “BRUSH” position for additional brushing action. 5. As a final step, use “drying strokes” (by not pressing the Spray Trigger) to remove as much liquid/ moisture as possible. Repeat this step as often as necessary. Note: If using the TurboBrush, move the switch to the “SUCTION” position. This activates the suction to remove the dirt and cleaning solution. After Cleaning 1. Turn Power Switch to OFF position. Note: If your unit has a Built In Heater turn the Heater Switch off. 2. Unplug Power Cord from outlet. Note: If a significant amount of Little Green formula/water remains, it is all right to leave it in the Clean/Solution Tank for your next cleaning task. 3. Empty and rinse the Dirty/Collection Tank after each use, OR when dirty water reaches the indicated maximum fill line. To remove the tank, lift up the Dirty/Collection Tank retainer lever and remove the tank from the unit. BRUSHSUCTIONIMPORTANT: Check the manufacturer’s tag before cleaning upholstery. “W” or “WS” on the tag means you can use your Little Green. If tag is coded with an “S” (with diagonal strike-through), or says “Dry Clean Only,” do not proceed. If manufacturer’s tag is missing or not coded, check with your furniture dealer. Tip: Tip: Deep clean-Check upholstery ing stairs and stuffing before high-traffic cleaning. Colored areas on a stuffing may regular basis bleed through can prolong the fabric when it carpet life. becomes wet. Tip: Before turning off the Little Green, vacuum up clean water to thoroughly rinse out the interior of the Vacuum Flex Hose. Then, lift the cleaning tool and point it upwards to drain any remaining water into the Dirty/ Collection Tank. Retainer Lever 3 800.237.7691 ug603-2302_1400_206.indd 8 3/6/06 11:40:11 AM 4. Disconnect the cleaning tool from the Spray Trigger by pushing down on button lock and pull- ing straight off (Do NOT twist tools to remove them) 5. After Cleaning (continued) After Cleaning (continued) Once removed from the Spray Trigger, all tools can be cleaned by rinsing under clean running water. The TurboBrush tool’s switch must be in “SUCTION” position before rinsing under clean running water. 6. Check Spray Nozzle for accumulated dirt or debris. If necessary, clean with soft bristle brush. Machine Storage 1. Wipe all surfaces with a soft cloth. 2. Wrap Power Cord around the Cord Wrap on the back of the Little Green. 3. Wrap Vacuum Flex Hose around the base of the unit and secure the Spray Trigger. 4. Store unit in protected, dry area, at room temperature (40. to 110.F). Note: For Little Green TurboBrush Models, onboard storage for the TurboBrush Tool has been provided on the back of the unit. Attach the TurboBrush to the unit by pressing it onto the holder firmly until the button snaps into hole. WARNING: Keep spray away from face. Failure to do so may result in personal injury. 9 800.237.7691 ug603-2302_1400_206.indd 9 3/6/06 11:40:12 AM Troubleshooting Water & Formula are draining out from the clean tank Possible Causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Blown fuse/tripped breaker 2. Replace household fuse or reset breaker Reduced spray or no spray Possible Causes Remedies 1. Spray Nozzle clogged 1. Clean Spray Nozzle 2. Clean/Solution Tank empty 2. Check/Refill Tank 3. Clean/Solution Tank insert clogged 3. Clean insert at bottom of Clean/Solution Tank 4. Pump needs priming 4. Gently lift Clean/Solution Tank while depressing the Spray Trigger OR Gently squeeze clean tank while depressing Spray Trigger Deep Cleaner won’t pick up cleaning solution Possible Causes Remedies 1. Poor Upholstery/Carpet Tool position 1. Reposition Upholstery/Carpet Tool on surface, follow recommended cleaning procedures 2. Dirty/Collection Tank is full 2. Empty Dirty/Collection Tank 3. Upholstery/Carpet Tool Brush worn 3. Replace with new Brush 4. Excess solution in Vacuum Flex Hose 4. Lift Tool and point upwards to allow water in Hose to flow into the Dirty/Collection Tank 5. Incorrect Cleaning Formula 5. Use BISSELL Little Green formula only TurboBrush attachment-Brush will not turn Possible Causes Remedies 1. Incorrect switch position on TurboBrush 1. Reposition switch to Brush position TurboBrush attachment– No Suction Possible Causes Remedies 1. Incorrect switch position on TurboBrush 1. Reposition switch to Suction position Thank you for selecting a BISSELL product. Please do not return this product to the store For any question or concern, BISSELL is happy to be of service. Contact us directly at 1-800-237-7691 800.237.7691 10 ug603-2302_1400_206.indd 10 3/6/06 11:40:12 AM Part Name 4” Upholstery/Carpet...