Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
out. There is a 2 second delay between signal drop-out scan resumption to allow time for any responding stations begin transmitting. • Seek mode Your transceiver stops scanning when detecting a signal and remains on the same frequency; the transceiver stays on this frequency even after the signal drops out and does not automatically resume scanning. Note: Pressing and holding [MONI] causes the transceiver to stop scanning; releasing [MONI] causes it to resume scanning. 8 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 26 VFO SCAN VFO Scan allows you to scan all frequencies from the lowest frequency to the highest frequency on the band. The current frequency step size {page 40} is used. 1 Select the desired band. 2 Press [VFO] (1 s). • The 1 MHz decimal blinks while scanning is in progress. • Scan starts at the frequency currently displayed. • To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). 3 To quit VFO Scan, press any key other than [LAMP], [MONI], and [F]. Note: The squelch must be closed for Scan to function. MEMORY SCAN Memory Scan allows all memory channels containing data to be scanned. 1 Press [MR] (1 s). • The 1 MHz decimal blinks while scanning is in progress. • Scan starts with the channel last recalled. • To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). 2 To quit Memory Scan, press any key other than [LAMP], [MONI], and [F]. Note: . At least 2 or more memory channels must contain data and must not be locked out. . The squelch must be closed for Scan to function. . The L0 to L9 and U0 to U9 memory channels and the priority channel are not scanned. . You can also start Memory Scan when in Channel Display mode. While Scan is being interrupted, the channel number blinks. . If you select “ONE” using Menu No. 2 (MR), memory channels on only the current band will be scanned; otherwise, memory channels on both VHF and UHF bands will be scanned. ¦ ¦ Memory channels scanning can 1 Recall the desired 2 Press [F], [0] to switch Lockout ON . • A star appears below the memory to indicate that the channel has 1 2 Note: The L0 to L9 and U0 to U9 memory channels and the priority channel cannot be locked out. MHz SCAN MHz Scan allows band. The current 1 the scan. For example, if the 438.400 MHz, then MHz Scan 438.000 MHz to 438.975 MHz. The exact upper limit depends on the step size 1 Press [VFO] to select VFO mode. 2 Select the desired band. 3 Press [MHz] (1 s) to start MHz Scan. • The 1 MHz decimal blinks while scanning is in progress. • Scan starts at the frequency currently displayed. • To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). 4 To quit MHz Scan, press any key other than [LAMP] , [MONI] , and [F] . 8 27 PROGRAM PROGRAM ¦ Setting Scan Limits You can store up to 10 scan ranges in memory channels L0/U0 to L9/U9. 1 Select the desired band. 2 Turn the Tuning control to display the desired lower limit. 3 Press [F] . 4 Turn the Tuning control to select a channel in the range L0 to L9. 28 5 Press [MR] . • The lower limit 6 Turn the Tuning control to display upper limit. 7 Press [F] . 8 Turn the Tuning control to select a matching channel in the range U0 to • If you have selected for example select U3. 9 Press [MR] . • The upper limit is stored in the channel. 10 To confirm the stored scan limits, press [MR] , then select the L and U channels. Note: . The lower limit must be lower in frequency than the upper limit. . The lower and upper frequency steps must be equal. . The lower and upper limits must be selected on the same band. 8 ¦ ¦ 1 Press [VFO] to select VFO 2 Select the desired 3 Select a frequency programmed scan limits. 4 Press [VFO] (1 s) . • The 1 MHz decimal blinks while progress. • Scan starts at the frequency currently • To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). 5 To quit Program Scan, press any key other than [LAMP] , [MONI] , and [F] . Note: . The squelch must be closed for Scan to function. . If the frequency step of the current VFO frequency differs from that of the programmed frequencies, you cannot use Program Scan. . If the frequency steps of the lower limit and upper limit differ, you cannot use Program Scan. . If the current VFO frequency is within more than one programmed scan range, the range stored in the smallest channel numbers is used. CALL/VFO Use Call/VFO the current VFO 1 Press [VFO] to select VFO mode. 2 Select the desired band. 3 Select the desired frequency. 4 Press [CALL] (1 s) to start Call/VFO Scan. • The 1 MHz decimal blinks while scanning 5 To quit Call/VFO Scan, press any key other [LAMP] , [MONI] , and [F] . CALL/MEMORY SCAN Use Call/Memory Scan to monitor both the Call channel and the desired memory channel. 1 Recall the desired memory channel. 2 Press [CALL] (1 s) to start Call/Memory Scan. • The 1 MHz deci...
Otros modelos de este manual:Radios - TH-G71A (2.53 mb)