Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
This manual contains important safety and operating instructions for the IC-718. PRECAUTIONS RWARNING HIGH VOLTAGE! NEVER attach an antenna or internal antenna connector during transmission. This may result in an electric shock or burn. RNEVER apply AC to the [DC13.8V] jack on the transceiver rear panel. This could cause a fire or ruin the transceiver. RNEVER apply more than 16 V DC, such as a 24 V battery, to the [DC13.8V] jack on the transceiver rear panel. This could cause a fire or ruin the transceiver. RNEVER let metal, wire or other objects touch any internal part or connectors on the rear panel of the transceiver. This may result in an electric shock. NEVER expose the transceiver to rain, snow or any liquids. AVOID using or placing the transceiver in areas with temperatures below –10°C (+14°F) or above +60°C (+140°F). Be aware that temperatures on a vehicle’ s dashboard can exceed 80°C (+176°F), resulting in permanent damage to the transceiver if left there for extended periods. AVOID placing the transceiver in excessively dusty environments or in direct sunlight. AVOID placing the transceiver against walls or putting anything on top of the transceiver. This will obstruct heat dissipation. WORD DEFINITION RWARNING Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE Inconvenience only. No risk of personal injury, fire or electric shock. During mobile operation, DO NOT operate the transceiver without running the vehicle’s engine. When transceiver power is ON and your vehicle’s engine is OFF, the vehicle’s battery will soon become exhausted. Make sure the transceiver power is OFF before starting the vehicle. This will avoid possible damage to the transceiver by ignition voltage spikes. During maritime mobile operation, keep the transceiver and microphone as far away as possible from the magnetic navigation compass to prevent erroneous indications. BE CAREFUL! The heatsink will become hot when operating the transceiver continuously for long periods. BE CAREFUL! If a linear amplifier is connected, set the transceiver’s RF output power to less than the linear amplifier’s maximum input level, otherwise, the linear amplifier will be damaged. Use Icom microphones only (supplied or optional). Other manufacturer’s microphones have different pin assignments, and connection to the IC-718 may damage the transceiver. TABLE OF CONTENTS 1 IMPORTANT ............................................................ i EXPLICIT DEFINITIONS .......................................... i PRECAUTIONS ........................................................ i 1 TABLE OF CONTENTS ...................................... 1 SUPPLIED ACCESSORIES .................................... 1 2 PANEL DESCRIPTION ................................... 2–8 n Front panel ....................................................... 2 n Function display ............................................... 5 n Rear panel ........................................................ 6 n Microphone (HM-36) ........................................ 8 3 INSTALLATION AND CONNECTIONS ........ 9–14 n Unpacking ........................................................ 9 n Selecting a location .......................................... 9 n Grounding ........................................................ 9 n Antenna connection ......................................... 9 n Required connections .................................... 10 n Advanced connections ................................... 11 n Power supply connections ............................. 12 n Liner amplifier connections ............................. 13 n External antenna tuners ................................. 14 4 FREQUENCY SETTING .............................. 15–19 n When first applying power .............................. 15 n Initial setting ................................................... 15 n VFO description ............................................. 16 n Frequency setting ........................................... 17 n Dial lock function ............................................ 19 5 RECEIVE AND TRANSMIT ......................... 20–34 n Mode selection ............................................... 20 n Squelch and RF gain ...................................... 20 n Function for receive ........................................ 21 n DSP function (option) ..................................... 23 n Filter selection ................................................ 24 n Filter setting .................................................... 25 n Function for transmit ...................................... 26 n Split frequency operation ............................... 30 n SWR ............................................................... 30 n Function for CW ............................................. 31 n Function for RTTY .......................................... 33 SUPPLIED ACCESSORIES The transceiver comes with the following accessories. Qty. q DC power...