Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Note:The operating time of 24 hours is based on the assumption that the baby unit transmits 25% of the time and is in standby mode for the rest of the time (when the baby does not make any sound). Note:When the parent unit batteries are charged for the first time, the operating time is less than 24 hours.The batteries only reach their full capacity after you have charged and discharged them four times. Note:When the batteries are running low, the battery check light flashes red. Put the small appliance plug in the parent unit and put the adapter in a wall socket to recharge the batteries. Note:When the parent unit is not connected to the mains, the batteries gradually discharge, even when the parent unit is switched off. Mains operation 1 Put the small appliance plug in the parent unit and put the adapter in a wall socket (Fig. 9). using the appliance 1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 10). Make sure the baby unit is at least 1 metre/3 feet away from the parent unit. Press and hold the on/off button 3 on the baby unit for seconds. (Fig. 11) The nightlight lights up briefly. , The ON light lights up. , Press and hold the on/off button 3 on the parent unit for seconds. (Fig. 1 ) The sound level lights light up blue briefly. , The battery check light lights up briefly. , The LINK light lights up red briefly and then starts to flash green while the parent unit tries , to establish connection with the baby unit. The LINK light on the parent unit flashes green until connection has been established. , This takes up to 0 seconds.The LINK light on the parent unit then lights up green continuously. If no link is established after 30 seconds, the LINK light on the parent unit flashes red and the , parent unit beeps from time to time. 5 Place the baby unit at least 1 metre/ feet away from your baby (Fig. 1 ). Position the parent unit within the operating range of the baby unit. Make sure it is at least 1 metre/ feet away from the baby unit (Fig. 1 ). For more information on the operating range, see section ‘Operating range’ below. EngliSh Operating range The operating range of the baby monitor is 300 metres/900 feet in open air. Depending on the surroundings and other disturbing factors, this range may be smaller. Indoors the operating range is up to 50 metres/150 feet. Dry materials Material thickness Loss of range Wood, plaster, cardboard, glass (without metal, wires or lead) < 30cm/12in 0-10% Brick, plywood < 30cm/12in 5-35% Reinforced concrete < 30cm/12in 30-100% Metal grilles or bars < 1cm /0.4in 90-100% Metal or aluminium sheets < 1cm/0.4in 100% For wet and moist materials, the range loss may be up to 100%. Features adjusting loudspeaker volume 1 Briefly press the volume + and – buttons on the baby unit until the desired loudspeaker volume for the baby unit has been reached (Fig. 15). Briefly press the volume + and – buttons on the parent unit until the desired loudspeaker volume for the parent unit has been reached (Fig. 16). Note: If you press the volume + and – buttons too long, the volume is not adjusted. Note:You only have to adjust the baby unit volume when you use the talk function (see below). Note: If the volume is set to a high level, the units consume more power. talk function You can use the TALK button on the parent unit to talk to your baby (e.g. to comfor t your baby). 1 Press and hold the TALK button and talk clearly into the microphone (Fig. 17). Release the TALK button when you have finished talking. Note:When you press the TALK button, you can no longer hear your baby. adjusting microphone sensitivity You can set the microphone sensitivity of the baby unit to the desired level.You can only change the microphone sensitivity when a connection between the baby unit and the parent unit has been established, i.e. when the LINK light on the parent unit lights up green continuously. Briefly press the SENSITIVITY button on the parent unit (Fig. 18). The sound level lights light up for approx. seconds to indicate the current sensitivity level. , Briefly press the volume + and - buttons on the parent unit until the desired microphone sensitivity level for the baby unit has been reached. Note: If you press the SENSITIVITY button and/or the volume + and – buttons too long, the microphone sensitivity is not adjusted. one light on = minimum sensitivity level , all lights on = maximum sensitivity level , 10 EngliSh Note:When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds and therefore transmits more often. As a result, the units consumes more power. Silent baby monitoring 1 Briefly press the volume down (–) button on the parent unit until the volume is switched off completely (Fig. 19). The volume is completely switched off when all sound level lights are out. As long as the baby unit does not detect a sound, all sound level lights on the parent unit are , out (Fig. 0). When the baby unit picks up a sound, one or...