Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
8). Make sure the baby unit is at least 1 metre/3 feet away from the parent unit. 2 3 Press and hold the on/off button 3on the baby unit until the green power-on light goes on. (Fig. 9) Turn the volume control to switch on the parent unit and to set the volume to the level you prefer (Fig. 10). The green power-on light goes on. , The LINK light on the parent unit flashes green until connection has been established. , This takes up to 30 seconds.The LINK light on the parent unit then lights up green continuously. Note: If no connection can be established, the LINK light on the parent unit flashes red. 4 Place the baby unit at least 1 metre/3 feet away from your baby (Fig. 11). 5 5 EngliSh Place the parent unit within the operating range of the baby unit. Make sure it is at least 1 metre/3 feet away from the baby unit. For more information on the operating range, see section ‘Operating range’ below (Fig. 12). operating range The operating range of the baby monitor is 200 metres/600 feet in open air. Depending on the surroundings and other disturbing factors, this range may be smaller. Wood, plaster, plaster cardboard, glass (without metal, wires or lead) <30cm/12in 0-10% Brick, plywood <30cm/12in 5-35% Reinforced concrete <30cm/12in 30-100% Metal grilles or bars <1cm/0.4in 90-100% Dry materials Material thickness Loss of range Metal or aluminium sheets <1cm/0.4in 100% For wet and moist materials, the range loss may be up to 100%. Features Digital signal confirmation The parent unit has a LINK light that continuously informs you of the status of the connection between the baby unit and the parent unit.You can set an aler t on the parent unit to notify you that the connection has been lost.The parent unit beeps and the LINK light flashes red when the connection has been lost. to activate the alert on the parent unit: 1 2 3 Slide the lid of the compartment for the rechargeable pack downwards to remove it (Fig. 5). Remove the rechargeable battery pack from the compartment (1) and remove the plug from the socket (2) (Fig. 13). Set the link alert switch in the compartment to the ‘on’ position (Fig. 14). -To switch off the aler t, set the link aler t switch to the ‘off ’ position (Fig. 15). 4 Slide the lid back onto the parent unit. adjustable sound sensitivity With the microphone sensitivity control on the baby unit, you can set the sound that is picked up by the baby unit to the desired level: low, mid or high. When the microphone sensitivity is set to ‘high’, the baby unit picks up all sounds. Note:The sensitivity of the baby unit can only be changed when there is a connection between the baby unit and the parent unit. 1 Set the microphone sensitivity control to the desired level (Fig. 16). The power-on light on the baby unit turns yellow when a sound is transmitted (Fig. 17). , Note:You can use your own voice as a sound reference. Note:When the microphone sensitivity of the baby unit is set to ‘high’, it picks up more sounds and therefore transmits more often. As a result, the units consume more power. 10 EngliSh adjustable loudspeaker volume You can adjust the volume on the parent unit to suit your surroundings. Turn the volume control of the parent unit to the volume you prefer (Fig. 18). Note:When the volume on the parent unit is set to a high level, it consumes more power. Sound level lights The parent unit continuously monitors the sound level in your baby.s room and the sound level lights let you know if there is any activity. If your baby cries, you see the sound level lights light up on the parent unit. -As long as the baby unit does not detect a sound, all sound level lights on the parent unit are out. -When the baby unit picks up a sound, one or more sound level lights on the parent unit go on. How many lights go on depends on the loudness of the sound picked up by the baby unit. -The sound level lights also operate when the parent unit is set to a low volume. nightlight The baby unit has a gentle nightlight that helps to soothe your baby back to sleep. 1 Press the baby unit nightlight to switch the nightlight on and off (Fig. 19). Channel selector Always make sure that the channel selectors inside the compar tments of both units are set to the same channel. With these channel selectors, you can select sixteen different channel positions. If you experience interference from other baby monitors, radios, TVs etc. that use the same channel, select a different channel. 1 Remove the lids of both units. Baby unit: (Fig. 3) , -Inser t a coin or screwdriver into the groove of the locking knob (1), turn the locking knob anticlockwise (2) and remove the lid. -If there are batteries in the compar tment, remove them. Parent unit: (Fig. 5) , -Slide the lid downwards to remove it. -Remove the batter y pack from the compar tment. Use a small, flat screwdriver to turn the channel selector of each unit to the desired position. Make sure both units are set to the same channel (Fig. 20). Test the connection 2 3 If you do...