Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
This Philips AVENT baby monitor provides round-the-clock suppor t by ensuring you can always hear your baby clearly without any distracting noise.The DECT technology guarantees zero interference and a cr ystal clear signal between the baby unit and the parent unit. English EN 7 a 3 Overview Press and hold to turn the parent unit Parent unit q sensitivity talk a j i h d e f c g m p k o n b l on or off b / Press to change the volume c Flashes red:The batter y pack is low in power. Flashes green: The batter y pack is in charging mode. d Press and hold to activate ECO mode In blue: ECO mode is enabled. e Sound level lights . Indicate the level of volume or microphone sensitivity . Indicate the sound level that the baby unit senses f Microphone g Speaker h link . In green:The parent unit is linked to the baby unit. . In red:The parent unit is searching for the baby unit. i sensitivity . Press to change the microphone sensitivity of the baby unit j talk . Press and hold to enable the talk function k Neck strap loop l Lid of battery compartment m NiMH 850mAh rechargeable battery pack n Connector for the adapter o Compartment for the battery pack p AC/DC adapter, with the same type as the one for the baby unit q Neck strap 8 EN 9 English EN Baby unit m b a c d g i j k f h e o n l p a Press and hold to turn the baby unit on or off b on In green: The baby unit is turned on. c PAGE Press to locate the parent unit Press to stop paging alerts d Microphone e Nightlight f Press to play the next lullaby g Press to play or stop a lullaby h / Press to change the volume i In green: The baby unit is running on batteries. Flashes red: The batteries are low in power. j Speaker k Press to turn the nightlight on or off l Lid of battery compartment m Four 1.5 V R6 AA non-rechargeable n Connector for the adapter o Battery compartment p AC/DC adapter Input: 100-240V AC Output: 6.0V DC, 500 mA Model number: SSW-1920US-2 10 EN 4 Get started Connect the baby unit to power You can connect the baby unit to a power supply or insert non-rechargeable batteries to operate it. Insert non-rechargeable batteries to guarantee an automatic backup in case of power supply failure. 1 Before you connect the baby unit to a power supply, remove the lid of the battery compartment. 2 Insert four non-rechargeable 1.5V R6 AA batteries with the correct polarity (+/-) as indicated. 3 Reattach the lid. 4 Connect a supplied adapter to the baby unit and to a power supply. Charge the parent unit Note Make sure that the parent unit is disconnected from the power supply and turned off. 1 Remove the lid of the battery compartment. 2 Insert the supplied rechargeable battery pack with the correct polarity (+/-) as indicated. 3 Reattach the lid. 4 Connect a supplied adapter to the parent unit and to a power supply to start charging. Tip The battery pack only reaches the full capacity after you charge it for four times. <= >? the operating time is less than 24 hours. The normal charging time is 8 hours, and the normal operating time is 24 hours. @ G? minutes before the battery pack runs out of power. 5 Use your babymonitor Link the parent unit to the baby unit: 1 Press and hold on the baby unit for two seconds. » The baby unit turns on, and all indicators on the baby unit light up @ 2 Press and hold on the parent unit for two seconds. » The parent unit turns on, and all indicators on the parent unit light up @ » The link @ parent unit star ts to search for the baby unit. » When the link is established, the link indicator lights up green. » If no link is established, the link @ beeps from time to time. Tip . It takes about 15 seconds to establish the link between the parent unit and the baby unit. Position the baby monitor: Note . For the optimal monitoring performance, keep the baby unit 1 to 2 metres (3.5 to 7 feet) away from the baby. . Place the baby unit away from window or noisy sources, like a fan,TV, or radio. The baby unit should always face towards the baby. 1 Keep the baby unit and the power cord at least 3.5 feet/1 meter away from your baby. > 3.5ft/1m 2 Keep the parent unit at least 5 feet/1.5 meter away from the baby unit to prevent acoustic feedback. > 5ft/1.5m 3 Use the parent unit in the operating range of the baby unit. Place the parent unit close by for better sound performance. Tip . When the parent unit is out of range of the baby unit, the parent unit beeps from time to time.The link @ . English EN 11 Operating range . In normal mode: Outdoors: up to 1000 feet/330 meters Indoors: up to 150 feet/50 meters . In ECO mode: Outdoors: up to 850 feet/260 meters . The operating range varies depending on the surroundings and other factors that cause interference. For interference from wet and moist materials, the range loss is up to 100%. For interference from dr y materials, see the following table: Dry materials Material Loss of thickness range Wood, plaster, card-< 12 in/3...