Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
PROGRAM BUTTON 21. NEXT/HOUR .. BUTTON 22. FM STEREO INDICATOR 23. RANDOM INDICATOR 24. SPEAKERS 25. VOLUME CONTROL 26. FUNCTION SELECTOR (CD/FM/AM/BUZZER) 27. TUNING CONTROL/DIAL INDICATOR 28. FM ATENNA WIRE 29. FM MODE SELECTOR (MONO/STEREO) 30. DIMMER SWITCH (LOW/HI) 31. BATTERY COMPARTMENT 32. AC POWER CORD POWER SOURCE This AM/FM Stereo CD Dual Alarm Clock Radio operates from AC 120V 60Hz line power supply. A 9V alkaline battery (not included) is also required to retain the normal and alarm time settings in the event of a power outage. AC OPERATION Plug the AC Power Cord into the AC 120V 60Hz power source. BACKUP BATTERY INSTALLATION 1. Open the Battery Compartment Door, following the polarity diagram shown in the Battery Compartment, connect one DC 9V battery (not included) to the battery clip which only fits one way to ensure the correct polarity. 2. Replace the Battery Compartment Door. IMPORTANT: Be sure that the battery is installed correctly. Wrong polarity may damage the unit. 3. For better performance and longer operating time, we recommend the use of alkaline-type battery. 4. If the unit is not to be used for an extended period of time, remove the battery. Old or leaking battery can cause damage to the unit and will void the warranty. 5. Do not dispose of battery in fire. Battery may leak or explode. TIME SETTING Note: In order for the clock to function properly, the clock has to be set the first time you use the Unit. The following procedure illustrates the setting of the Clock at 2:15 PM. 1. Connect the AC cord to an AC 120V 60Hz power outlet. Make sure to use an outlet that is always “live”. Do not use an outlet that is controlled by a wall switch. 2. When the unit is plugged in the first time, the Display will show flashing “12:00” (AM). 3. While the Display is flashing, press repeatedly and release the HOUR .. Button until the correct hour is displayed. Note: For 12 Hour format, there is a PM INDICATOR (PM) located in the upper left-hand corner of the DISPLAY. This indicator will light when the time range falls within the “PM” range when setting the clock. The time is in the “AM” range if this indicator is not lit. It is important that the “AM” or “PM” setting is correct for proper operation of the Alarm function. 4. Press repeatedly and release the MINUTE .. Button until the correct minute is displayed. 5. Press the CLOCK Button once to complete the setting. Note: If you want to reset the time, first press the CLOCK Button once then repeat steps 3 to 5 to complete the setting. CHANGING 12/24 HOUR FORMAT Press and hold the CLOCK Button, the clock will change to 24 Hour format, and vice versa. SETTING ALARM TIME This unit allows you to set two different wake-up times, which you can choose to, use independently or simultaneously AL1 or AL2 or AL1 and 2. 1. Press the ALARM1 or ALARM 2 Button once. The Display will change from the current time to wake up time and begin flashing. The ALARM1 or ALARM 2 indicator lights. 2. While the Display is flashing, press repeatedly and release the .. Button until the desired hour appears in the Display. Note: For 12 Hour format, there is a PM INDICATOR (PM) located in the upper left-hand corner of the Display. This indicator will light when the time range falls within the “PM” range when setting the Alarm. The time is in the “AM” range if this indicator is not lit. It is important that the “AM” or “PM” setting is correct for proper operation of the Alarm function. 3. Press repeatedly and release the .. Button until the correct minute is displayed. 4. To complete the setting process press the respective ALARM1 or ALARM 2 button once. Note: Press ALARM1 or ALARM 2 buttons once to turn the respective Alarm function off. The respective ALARM1 or ALARM 2 Indicator will go off. DIMMER OPERATION 1. Set the DIMMER SWITCH to ”HI” for a bright LED Display under normal room illumination. 2. Set the DIMMER SWITCH to ”LOW” for a dim LED Display in the dark. RADIO RECEPTION 1. Press the POWER Button to turn on the unit. The POWER INDICATOR lights. 2. Set the FUNCTION Selector to AM or FM position. 3. Set the FM MODE Selector to MONO or STEREO if FM Band is selected. Note: i. For FM reception, the unit provides FM MONO/STEREO selection. If you select FM STEREO band, the FM STEREO Indicator will light when a strong FM stereo broadcast is received. ii. To receive a weak (noisy) FM station, set the FM MODE Selector to MONO position. The reception then may be improved, but the sound is monaural (MONO). 4. Turn the TUNING Knob for the desired station and adjust the volume using the VOLUME Control. 5. When you have finished listening press the POWER Button again to turn the unit “Off”. The POWER Indicator goes “Off”. TIPS FOR BEST RADIO RECEPTION AM The AM ferrite bar antenna is inside the cabinet. If AM reception is unsatisfactory, try turning the entire unit slightly until you find the direction that provides the best reception for the desired station. FM Make sure the FM Wi...