Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
If the bass is kept at a lower level while operating on batteries, distortion willbe kept to a minimum. To turn the bass up, rotate the BASS knob clockwise. t TREBLE KNOB Treble can be used to raise the range of highs to improve music fidelity. It can also be used toadjust for your hearing to make voices more legible. To turn the treble up, rotate the TREBLE knob clockwise. y AM RF GAIN KNOB The AM RF GAIN control is used to: 1) Reduce overload from an overly strong nearby station. If you have background CCRadio SW Page 15 Features and Operation Explained — Front of Radio distortion, try reducing the AM RF GAIN for a clearer signal; and 2) Reduce static. When a signal is amplified by the RF amplifier, background noise is generally amplified out of proportion to the audio signal. This is due to the inherent natureof solid state chips. By reducing the AM RF GAIN control you can reduce static while keeping a decent audio signal. TUNING TIP: The AM RF GAIN knob should be set to full clockwise to begin. AM and SW station signal strengths are indicated on the display with signal bar graph. If youexperience background noise or overlapping stations when tuning to your station, turn the AM RF GAIN down or counter clockwise and it will reduce interference in many cases. u HEADPHONE JACK The HEADPHONE jack output will be in stereo for FM stations that broadcast in stereo. Set AM/SW–FM band switch o to FM STEREO position to hear FM stations in stereo with headphones. will be displayed when the AM/SW–FM band switch is set to FM STEREO and a stereo signal is received. HEADPHONE JACK TIP: When using headphones, turn down the volume before plugging in headphones. i AM/SW SWITCH This switch is used with AM/SW–FM band switch o to select AM band or SW band ranges SW1, SW2 and SW3. o AM/SW–FM BAND SWITCH This switch is used to select AM and SW WIDE and NARROW modes. It is also used to select FM MONO and STEREO modes. The MONO setting will give the best reception while listening to a weak station. TUNING TIP: To tune to SW, set this switch to AM WIDE. Then using the AM/SW BAND switch i, select either SW1 , SW2 or SW3 . To tune to AM, set this switch to AM WIDE . Then set the AM/SW BAND switch i to AM. If you experience overlapping stations or background noise, try setting the switch to NARROW . When tuning FM stations, set the switch to STEREO only when you are listening with headphones. The word will be displayed when a stereo signal is received. Page 16 CCRadio SW Features and Operation Explained — Front of Radio p LCD DISPLAY 53 42 8 61 9 11 10 12 7 1) BATTERY Symbol 7) MEMORY Location (1 -10) 2) AC ADAPTER Symbol 8) DIAL SPEED Indicators 3) SLEEP Timer/SNOOZE Status 9) FREQUENCY/CLOCK Display 4) KEY LOCK On/Off 10) DUAL TIME Indicator 5) ALARM Status and Type 11) Indicates BAND In Use 6) Signal Strength Meter 12) STEREO Reception [ SNOOZE BAR The SNOOZE bar has two functions: 1) The SNOOZE bar is used to pause an alarm. See SETTING THE ALARM on page 11. To snooze, press and release the SNOOZE bar [ on top of the radio, while the alarmis going off. The alarm icon will flash on the display. Each time the SNOOZE bar is pressed, the alarm will be paused for five minutes. You can snooze up to four times andthen the alarm will be automatically shut off. 2) When the radio is off but power is applied, pressing the SNOOZE bar [ turns off the beep while using the HOUR when reaching the end of a radio band. < or the MINUTE < buttons. There is still a beep ] LIGHT BAR Press and release LIGHT bar to turn the LCD display light on for eight seconds. If you wantthe display light to remain on, press and hold the LIGHT bar for 2 seconds or more. Press and release the LIGHT button again to turn the LCD display light off. CCRadio SW Page 17 Features and Operation Explained — Left Side A LINE OUT LINE OUT is used to send the radio s audio to an external amplified speaker or stereo system. It is a fixed output level designed to work with external systems. The radio s VOLUME , BASS and TREBLE controls do not function when using LINE OUT to an external system. An optional patch cord to your amplified speakers or stereo system will be needed for this connection. LINE OUT TIPS: When using LINE OUT , set AM/SW–FM switch o to FM STEREO position to hear FM stations in stereo with external systems. The word will be displayed when a stereo sign is received. S BATTERY SIZE SWITCH The BATTERY SIZE switch is used to select between AA and D size batteries. To power the radio with batteries, slide BATTERY SIZE switch S to the size of battery being used. Insert 4 batteries into the Battery compartment L, paying close attention to THE orientation ofthe batteries + and – ends. The LCD will display a with fresh, new batteries. When the batteries are low, the icon will display. If the batteries are too low to run the radio, the icon will flash on the display, and ultimately, the radio will automatically shut off . Batteries are also used to maintain clocks, alarms...