Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
-If the appliance has been subject to excessive shock by being dropped, or the cabinet has been damaged. Servicing Do not attempt to service the appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Replacement parts When replacement parts are required, be sure the service technician has used replacement parts specified by Sony that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check Upon completion of any service or repairs to the appliance, ask the service technician to perform routine safety checks (as specified by Sony) to determine that the appliance is in safe operating condition. AC power cord FM wire antenna 1 2 3 4 5 BAND SUMMER T. CLOCK TUNE/TIME SETD.S.T. A RADIO B BUZZER ALARM ALARM MODE WAKE UP STATION SELECT/ WEATHER STATION PRESET OFF ONRADIO ALARM RESET SLEEP SNOOZE / DATE / SLEEP OFF VOLUME BRIGHTNESS L H WEATHERTV FM AM PM SLEEP PRESET MHz kHz ARADIO•ALARM•BBUZZER AC power cord FM wire antenna 1 2 3 4 5 BAND SUMMER T. CLOCK TUNE/TIME SETD.S.T. A RADIO B BUZZER ALARM ALARM MODE WAKE UP STATION SELECT/ WEATHER STATION PRESET OFF ONRADIO ALARM RESET SLEEP SNOOZE / DATE / SLEEP OFF VOLUME BRIGHTNESS L H WEATHERTV FM AM PM SLEEP PRESET MHz kHz ARADIO•ALARM•BBUZZER Setting the Clock 1 Plug in the clock radio. "AM 12:00" will flash in the display. 2 Press CLOCK for a few seconds. You will hear a beep and the year will start to flash in the display. 3 Press TUNE/TIME SET + or – until the correct year appears in the display. 4 Press CLOCK once. 5 Repeat steps 3 and 4 to set the month, date, hour, and minute. After setting the minute, press and release CLOCK to start the counting of the seconds. • To display the year and date, press SNOOZE/ DATE/SLEEP OFF once for the date and within 2 seconds press it again for the year. The date or year will appear in the display for a few seconds and then the display returns to the current time. When SNOOZE/DATE/SLEEP OFF is pressed while the SNOOZE function is operating, the year and date will not appear in the display. • To set the current time rapidly, hold down the + or – button. • To set the current time from zero seconds, release CLOCK with the time signal at step 5. To change the display to the daylight saving time (summer time) indication Press D.S.T./SUMMER T. “ ” is displayed and the time indication changes to summer time. To cancel the summer time indication, press D.S.T./SUMMER T. again. Playing the Radio Manual Tuning 1 Press RADIO ON to turn on the radio. The band and frequency will appear in the display for a few seconds and then the current time indication returns to the display. 2 Press BAND repeatedly to select the desired band. 3 Use TUNE/TIME SET + or – to tune in the desired station. The FM frequency advances or reverses in 0.1 MHz channel steps and the AM frequency in 10 kHz channel steps. A beep sounds when the upper or lower extremity of the band range is reached. 4 Adjust volume using VOLUME. • To turn off the radio, press RADIO OFF. • To improve reception TV/WEATHER/FM: Extend the FM wire antenna fully to increase FM reception sensitivity. AM:Rotate the unit horizontally for optimum reception. A ferrite bar antenna is built in to the unit. • To check the current station, press the + or – button lightly. The band and frequency are displayed for a few seconds, after which the current time indication returns to the display. • If the radio alarm A RADIO comes on while the radio is playing, the station switches to the frequency set under preset number 1. To listen to the WEATHER band 1 Press RADIO ON to turn on the radio. 2 Press WEATHER to switch to the WEATHER band. “WEATHER” will appear in the display. 3 Press TUNE/TIME SET + or – repeatedly until the desired channel appears in the display. To switch back to the previous band, press BAND. To set the brightness of the backlight Set BRIGHTNESS to H (high) or L (low) to make the display more visible. Preset Tuning You can preset up to five stations for one-touch tuning, one under each of preset buttons 1 to 5. Presetting a station Example: To set AM 1260 kHz in preset button 2. 1 Press RADIO ON to turn on the radio. 2 Tune in the station you want to preset. (See “Manual Tuning”) 3 Hold down the desired STATION•SELECT/PRESET button (in this case, 2) until you hear two short beeps. AM PRESET kHz The frequency will appear for a few seconds and then the display will return to the current time. • When using the radio alarm, preset the station you wish to serve as the alarm under preset button 1. To change a preset station Press the preset number again after tuning in manually to a different station. The previous station is replaced by the new one. Tuning in a preset station 1 Press RADIO ON to turn on the radio. 2 Press the STATION•SELECT/PRESET button under which the desired station is stored. 3 Adjust v...