Votos - 2, Puntuación media: 3.5
(
)
)
|
Fotos y especificaciones Hyundai H-1614 |
Resumen del manual
Please observe correct battery polarities or the set will not work. • Close the battery compartment cover. • When the battery is exhausted, it should be removed from the set to prevent leakage. • When replacing batteries or changing to use external power, you must turn off the power and change the batteries in thirty seconds, otherwise the stored information will be lost. Use External Power Please use output DC 3 V 300mA regulating external direct current power, check the positive and negative of the plug ©-<*-© Radio Operation Power Switch Press the Power Switch/Sleep off button once to turn on the radio, the last band frequency before turning off the radio is displayed. Press the Power Switch/Sleep off button again to turn off the radio, the time is displayed. Adjust Volume 3 When you listen to the radio, please turn the knob to adjust it to your desired volume. Band Selection In receiving state, press the Band / mode button to choose FM, MW, SW programs. Manual Search • Press the Power Switch/Sleep off button to turn on the radio. • Press the Band /mode button to select the band. • Press the up tuning/hour button or down tuning/minute button to select your desired station frequency. With each press the frequency varies one step until the station is found. Attention: • Manual searching station mode is fit to search weak signal station. Automatic Search • Press the Power Switch/Sleep off button to turn on the radio. • Press the Band / mode button to select one band of them. • Keep the up tuning button or down tuning button pressed, when you see the display frequency automatically change, release the button, when there is a station, it will stop searching automatically. • In the course of automatic searching, press the up tuning/hour or down tuning/minute button, to stop searching. Attention: • Automatic searching station mode is fit to search strong signal station. • In the course of automatic searching, if the digit on the display screen varies slowly, it means that there is weak signal station nearby, you can change to use manual to search station. Frequency Change Law • Receiving FM, press the up tuning/hour or down tuning/minute button once, the frequency increases or decreases 0.1 MHz. • Receiving SW, press the up tuning/hour or down tuning/minute button once, the frequency increases or decreases 0.005 MHz. • When receiving MW, press the up tuning/hour or down tuning/minute button once, the frequency increases or decreases 9KHz. Memory Stations • Tune the desired station with auto or manual search. • Press the memory/time set button, the "MEMORY" is flashing on the display screen. • Press the Memory + or the Memory - to select stored address. In 5 seconds press the memory/time set button again to confirm the stored address, the station frequency has been stored in the address. Attention: You can store 10 stations in each band. If in 1-10 address the station frequency already exists, store new frequency according to the above-mentioned methods, the old frequency will be cancelled. 4 Store scan In receiving state press the Alarm button/store scan button once, it will begin to scan station, in the course of searching, when there is a station, it will store it automatically, and then hold on. In the course of automatic scanning press the Alarm button/store scan button once again, it will discontinue scan. Attention: 1.In the course of automatic scanning, if the reception is not clear please change to use manual mode to search station. 2.When using the store scan function, the old frequency will be covered with the new station. Using Stored Stations In receiving state, press the Band / mode button to select band, press the Memory + or the Memory - button to select the station which is saved in the memory. DX Local switch Local and DX sensitivity switch is set in the radio, it is convenient for you to receive SW, FM program under different circumstances, In general, please set the switch to the position of DX; if you receive Local stations with strong signal or meet strong electric jam, please set the switch to the position of Local. F F DX/LOCAL switch Stereo/Mono Switch • When receiving FM stereo station, please move the Mono/Stereo switch to stereo position, LCD will display " ". • When receiving Mono station, move the switch to mono position. • Suggestion: When receiving stereo station with weak signal, move the switch to Mono position. Earphones Socket For private listening please insert the earphones in the Earphone socket (the speaker inside the radio disconnects automatically), you can listen to the radio by earphones. Earphone Socket mis-operate, or the radio is Reset Button The microcomputer chip is used to handle radio signal in the unit, when you change battery or change-over external power, jammed, the microcomputer chip in the unit may come into in the state of dead cycle, it is out of order. The main signs of dead cycle: • There is ...