Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
When pressing the / keys, the displayed character entry cycles through A ~ Z, 0 ~ 9 and a space (default settings). You can also assign a character to an optional key and later press that key to recall the assigned character: A ~ Z, a ~ z, 0 ~ 9, or a space and characters. When using the microphone keypad, you can enter characters as shown in the table below: DTMF Key Default Character Cycle 1 1 2 A > B > C > 2 3 D > E > F > 3 4 G > H > I > 4 5 J > K > L > 5 6 M > N > O > 6 7 P > Q > R > S > 7 8 T > U > V > 8 9 W > X > Y > Z > 9 0 [space] > 0 15 SCAN Scan is useful for monitoring signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops on a channel if a signal is present. To begin scanning, press the key programmed as Scan. • The icon appears on the display. • The channels included in the scan list are scanned. • When a signal is detected on a channel, Scan pauses on that channel. The transceiver will remain on the busy channel until the signal is no longer present. When the signal “drops out”, the transceiver will remain on the channel momentarily before Scan resumes. This delay time is programmed by your dealer. If a signal is received during the delay time, the transceiver will remain on the same channel. To stop scanning, press the Scan key again. Note: In order for Scan to operate, there must be at least 2 channels added to the scanning sequence. If there are less channels than this, Scan will not operate. TEMPORARY CHANNEL LOCKOUT If a key is programmed with the Scan Delete/Add function, each channel can be locked out of the scan sequence manually. During scan, you can temporarily remove specific channels from the scanning sequence by selecting them and pressing the Scan Delete/Add key. • The icon (right side) no longer appears on the display for that channel. • The channel is no longer scanned. However, when scanning is ended and restarted, the channels will reset and the channel will again be in the scanning sequence. PRIORITY SCAN A Priority channel must be programmed in order for Priority Scan to function. When using a single Priority channel, the transceiver will automatically change to the Priority channel when a call is received on it, even if a call is being received on a normal channel. When using dual Priority channels, Priority channel 1 is given precedence over Priority channel 2. So, if a call is received on Priority channel 1 while a call is already on Priority channel 2, the transceiver will automatically change to Priority channel 1. • “ ” appears on the display when the channel is Priority channel 1, “ ” appears when the channel is Priority channel 2, and “ ” appears when the channel is both Priority channel 1 and 2. 16 SCAN REVERT The Scan Revert channel is the channel selected when you press the microphone PTT switch to transmit during scan. Your dealer can program one of the following Scan Revert channels: • Last Called + Selected: The last channel on which you received a call is assigned as the new revert channel. If the channel has been changed, the newly selected channel is assigned as the new revert channel. • Selected: The last channel selected is assigned as the new revert channel. • Selected + Talkback: If the channel has been changed, the newly selected channel is assigned as the new revert channel. The transceiver “talks back” on the current channel. • Priority 1/ Priority 2: If your dealer has programmed a Priority channel (either Priority 1 or Priority 2), this channel is the revert zone and channel. • Priority 1 + Talkback/ Priority2 + Talkback: If your dealer has programmed a Priority channel (either Priority 1 or Priority 2), this channel is the revert zone and channel. The transceiver “talks back” on the current receive channel. SCAN DELETE/ADD You can add and remove zones and/or channels/group IDs to and from your scan list. 1 Select your desired zone and/or channel/group ID. 2 Press the key programmed as Zone Delete/Add (to add/remove zones) or Scan Delete/Add (to add/remove channels/group IDs). • You can also press and hold the key programmed as Scan Delete/Add to add/ remove zones. PRIORITY-CHANNEL SELECT If the Priority channel has been set as Operator Selectable by your dealer, you are also able to reprogram the Priority mode. 1 Select your desired zone and channel. 2 Press the key programmed as Priority-chanel Select, or press and hold the key programmed as Scan. • A list of channel types appears on the display. 3 Press the / keys to select the channel type for your current channel. • You can set the channel as “NORMAL”, “PRIORITY 1”, “PRIORITY 2”, or “PRIORITY 1&2”. 4 Press the key to save the setting and exit Priority-channel Select Mode. 17 FleetSync is an Alphanumeric 2-way Paging Function, and is a protocol owned by JVC KENWOOD Corporation. FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming. Your dealer can set up either FleetSync or...
Otros modelos de este manual:Radio - NX-901 (399.5 kb)