Iniciar sesión:
Votos - 5, Puntuación media: 4.4 ( )

Manual de usuario BT, modelo 1505

Fabricar: BT
Tamaño del archivo: 1.64 mb
Nombre del archivo: solas_1500_user_guide.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


When the alarm time is reached, the and ALARM ON" flash on the handset display, and the alarm tone rings for 45 seconds. You can press any key to disable the alarm. If the snooze function is activated, the alarm will sound again at the end of the snooze period of seven minutes. You can also press and hold while the alarm is sounding, to stop the alarm and turn off the snooze function. Note: a. A key press will still disable the alarm even if the handset keypad is locked when the alarm rings. b. The alarm volume level is the same as the settings of the handset ringer volume. If the handset ringer is set to VOLUME OFF, the alarm still sounds at VOLUME 1 level. c. During an external call or internal call, if an alarm is set and when the alarm time is reached, the and “ALARM ON” will still flash. An alarm tone will be emitted from the earpiece to alert the user the alarm time is reached. Once the user presses any key or presses and holds to disable the alarm, the display will revert to the call duration. d. During paging or ringing, the alarm will not sound when the alarm time is reached. However, if the snooze function is enabled and there is no paging or ringing, the alarm will sound again at the end of the snooze period. 7.2.1 Turn on/off the Alarm 1. Press

and to select HS SETTINGS. 2. Press <0K> and to select ALARM. 3. Press <0K> and to select ON/OFF. 4. Press <0 K> to confirm. Note: If ON is selected, you will be asked to set the alarm time. 7.2.2 Set the Alarm Time (If Alarm time is set to be ON) 1. Follow Steps 1 to 4 in Section 7.2.1. 2. Enter the alarm time in 24 hour format. 3. Press <0K> to display "SNOOZE". 4. Press <0K> and to select snooze ON or OFF. 5. Press <0 K> to confirm. 7.3 Handset Settings 7.3.1 Set the Ringer Melody for Internal Calls 1. Press and to select HS SETTINGS. 2. Press <0K> and to select RING SETUP 3. Press <0K> and to select INT RING. 4. Press <0K> and to select the melody you want to hear for internal calls. 19 7.5 Registration IMPORTANT: When you purchase a Solas 1505 system, all handsets are already registered to your base, so you do not need to register them. Handset registration is only necessary when you buy extra handsets or if a handset has become faulty. You can register additional handsets to have up to five handsets per base unit, with each handset's number (1 to 5) shown on its display. (Note: each handset can only be registered to one base.) To register a new handset to your base: 1. Press and hold on the base station for more than five seconds, to put the base station into registration mode. (Note: there is no feedback to know it is in registration mode.) It will stay in registration mode for about 1 minute, so the following handset sequence must be completed within this time. 2. Press and to select REGISTRATION. 3. Press <0K> and you are requested to enter the 4-digit system PIN. 4. Enter the 4-digit system PIN. 5. Press <0K> to confirm, and the display will show SEARCHING. If the handset registration is successful, you will hear a confirmation tone and the will stop flashing. This may take a short while. The handset will automatically be allocated the next available handset number. This handset number is shown in the handset display in standby mode. If the handset registration is unsuccessful, the will still flash and the display will return to "REGISTER", so you will need to repeat the registration process. 7.6 Reset Your Phone You can reset your phone to the default settings . Alter a reset, all your personal settings, call list entries and redial list entries, will be deleted but your phonebook remains unchanged. 1. Press and to select DEFAULT. 2. Press <0K> and you are requested to enter the 4-digit system PIN. 3. Enter the 4-digit system PIN. 4. Press <0K> to display CON FIRM? 5. Press <0K> to confirm, and the phone will be reset to its default settings. 8 TROUBLESHOOTING When connect to a PBX, no and/or wrong connection after dialling. "SEARCHING" is displayed. The call does not work. No display. Causes a.The connection cord of the base station is not plugged in. b.The adapter cord is not plugged in correctly in the base station. c. Another handset is using the base to make a call. d. Wrong telephone line cord Dialling prefix is needed. a. Base station out of b. Base station not connected to mains. Service not activated oi wrong setting Empty battery Solutions a.Check the connections. Unplug and plug back in the mains. Check that the telephone cord has been plugged into the base station and the phone socket. b.Check the base station plug and the 230V plug (remove and plug-ir c.Wait until the line is unoccupied. d.Use the original telephone line cord supplied Insert the dialling pre...

Otros modelos de este manual:
Los teléfonos inalámbricos - 1505 (1.64 mb)
Los teléfonos inalámbricos - 1505 (1.64 mb)
Los teléfonos inalámbricos - 1505 (1.64 mb)
Los teléfonos inalámbricos - 1505 (1.64 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría