Votos - 3, Puntuación media: 4 ( )

Fabricar: Cortelco Tamaño del archivo: 375.2 kb Nombre del archivo: 8012_manual.pdf Idioma del manual:

If pressed during a call, activates the speakerphone. End Key - End a call. If pressed and held, powers off the handset Left/Right Soft Keyimmediately over it in the display. - Performs the function indicated by the text *Key - Press and hold to lock the keypad. Set up a conference call as described on Page 35. 16 Navigation Key Up/CID Key - Scrolls up through list and menu options. Increases the receiver or speakerphone volume during a call. Enters the CID book as described on Page 18. Down/Phonebook Key - Scrolls down through list and menu options. Decreases the receiver or speakerphone volume during a call. Enters the phonebook as described on Page 26. Left/Int Key - Set up an intercom call to another handset. Transfer a call to another handset. Set up a conference call with an external line and an intercom handset. Right/Redial Key - Enter the redial book as described in Page 16. Insert a pause when pre-dialing. 17 Icons New Call - One or more calls have been received. MSG Waiting - One or more voice messages have been received. Off Hook - The line is in use. Speakerphone - Speakerphone function is in use. 18 Alarm - The alarm is activated. Signal - Indicates the signal strength. Blinks if the handset is too far from the base. Battery - Shows battery charge level Keypad Lock - Keypad is locked. 19 Installation Line and Power Connection 1. Connect the phone line cord to the telephone line jack in the Connect the other end of the line cord to a telephone outlet. 2. Connect the AC power adapter to the base power jack. Plug the AC power adapter into an AC outlet. 20 Battery Installation Two rechargeable Ni-MH AAA size batteries come with the 8012. These must be installed before use. 1. Slide the battery cover in the direction shown below and remove. 2. Install the batteries as shown below. Care must be taken to install in the correct polarity. The 8012 may be damaged if batteries are inserted in incorrect polarity. 3. Reinstall the battery cover. Replace the batteries when they fail to return to a full charge after recharging. Use only Ni-MH rechargeable batteries. Never use other battery types such as alkaline. 21 Charging Handset The handset should be charged for 15 hours before initial use. To charge the handset, place it in the base. If the handset is off, it will automatically turn on. To turn the handset off, press until the display turns off. To turn the handset on, press until the display turns on. If the handset is able to find a base, the display will show the handset number, the handset name (if one is assigned), the signal icon, battery icon, and the current time. If the handset cannot find a base, it will display “Searching...” 22 DSL Interference If the 8012 is used on a line with DSL service, it may be filter. A filter may be obtained from the DSL provider. It should by used if noise is heard during conversations or Caller ID is not functioning properly. 23 Basic Functions Making a Call 1. Remove the handset from the base and press 2. Dial the telephone number. Making a Call - Standby Mode 1. Enter the telephone number (up to 32 digits). Use to enter a pause. Use the Erase soft key to correct mistakes. 2. Press to dial the number. Receiving a Call When a call is received, the InUse indicator on the base will blink. Normally, the caller’s phone number will be displayed. If the caller cannot be identified, only the NewCall information will display. 24 or or 1. If Auto Answer has been activated and the handset is in the handset to answer the call. 2. Otherwise, press to answer. Notes: After the call is terminated, the display will show the call duration. a polyphonic ringtone is set, the ringtone may contiue for up to 4 seconds call is answered at another phone. To change the ringer volume, press while the phone is ringing. Mute During a conversation, the microphone of the 8012 can be muted so that the distant party cannot hear what is being said. To mute the microphone, press the MUTE soft key. The display will show “CALL MUTED.” To unmute the microphone, press the MUTE soft key again. 25 or or Volume Control During a conversation, pressing will adjust the handset receiver or speakerphone volume level. Volume can be adjusted in 5 steps. Message Waiting If a voice message is received, the display will show the icon and “MSG WTG ON “ To deactivate the icon, press the key in standby mode, then press and hold the 4 key. Finally, press to return to standby mode. Ringer Settings Perform the following steps to change the ringer tone or volume. These settings can apply to either external calls (from the telephone company) or internal calls (from other handsets registered to the same base). 1. Press the Menu soft key. 2. Press or to choose HS Settings. 26 3. Press the Select soft key. 4. Press to choose Ring Setup. 5. Press the Select soft key. 6. Press the Select soft key to choose INT Ring, or press the key to choose EXT Ring. 7. Press the Select soft key. 8. Press to choose Melody or Volume. 9. Press...

Descargar ahora

Introduzca dos números de la imagen: