3 Press S, then press until PGM flashes. DIAL ERASE PPGGMM 973-555-0123 5/01 5:40PM OLD28 4 Press Sthree times to store the call record in memory without editing. DISTINCTIVE RING?Y 973-555-0123 5 Press to select Y or N for distinctive ring option. 6 Press S. You’ll hear a beep confirming that the name and number were stored. Display Screen Messages Screen Displays: When: PRIVATE The other party is blocking name and/or number information. OUT OF AREA Your phone company is unable to receive information about this caller’s name and/or number. Turn off the Base NEW CALL Indicator After reviewing new calls, press the Oon the handset —OR— Place the handset in the base. 17 Charge the Handset Battery Pack • This battery should remain charged up to six days with the ringer turned on and up to 10 days with the ringer off. A fully charged battery provides an average talk time of about 10 hours. • The battery pack needs charging when: — A new battery is installed in the handset. — The phone beeps twice every five seconds. — The screen displays BATTERY LOW and the low battery icon. • Place the handset in the base so the CHARGING light turns on. The battery pack is typically fully charged in 10 hours. • You can keep the battery fully charged by returning the handset to the base after each use. • If you repeatedly get a low battery indicator, even after charging overnight, the battery should be replaced. Use only Replacement Battery 2214 (SKU# 23403) or Battery 3301 (SKU# 91076). CAUTION: To reduce the risk of fire or injury to persons or damage to the telephone, read and follow these instructions carefully: Charge the battery provided with or identified for use with this product only in accordance with the instructions and limitations specified in the User’s Manual, Part 1. BATTERIES 1450_book_1ATT 3/26 3/26/02 4:59 PM Page 18 BATTERIES 1450_book_1ATT 3/26 3/26/02 4:59 PM Page 18 18 1450_book_1ATT 3/26 3/26/02 4:59 PM Page 19 1450_book_1ATT 3/26 3/26/02 4:59 PM Page 19 BATTERIES Replacing the Handset Battery Pack 1 Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cover downward. 2 Lift out the old battery pack and disconnect. 3 Align the two holes in the new battery pack’s plug with the socket pins, and snap the plug into place. Place the battery pack in the compartment with the wires in the lower left corner, along the bottom of the battery pack. 4 Replace the cover by sliding it up into place. 5 The new battery pack must be charged before using the phone. Place the handset in the base and allow it to charge for at least 12 hours the first charge. The telephone might operate before that, but for best performance, let the battery pack charge fully. 19 1450_book_1ATT 3/26 3/26/02 4:59 PM Page 20 1450_book_1ATT 3/26 3/26/02 4:59 PM Page 20 IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. For Customer Service, visit our website at or call 1 800 222–3111. Please retain your receipt as your proof of purchase. If the phone doesn’t work at all, check these items first: • Make sure the AC adapter is plugged into an outlet not controlled by a wall switch. • Make sure the telephone line cord is plugged firmly into the base unit and the modular jack. • Make sure the base antenna is fully upright. • If the handset does not beep when you press P, the battery might need charging. • Make sure the battery pack is installed correctly. • If you have dial pulse (rotary) service on your phone line, make sure the dial mode is set to dial pulse (see INSTALLATION). • Microwave appliances may cause interference with this phone. If you experience interference, move away from the microwave If the above suggestions don’t solve the problem, try re-initializing the handset and base: 1 Disconnect the power to the base. 2 Remove the handset battery pack. 3 Wait a few minutes. 4 Connect the power to the base. 5 Insert the handset battery pack. 6 Put the handset in the base to re-initialize. If you hear a two-beep signal when you try to use the handset: • You might be out of range. Move closer to the base and try again. • If moving closer to the base doesn’t help, try following the directions above for re-initializing the handset and base. If the phone does not ring when you receive a call: • Make sure the handset ringer is on. • Make sure the telephone line cord is connected firmly to the base and the telephone jack. • Make sure the AC adapter is plugged firmly into an outlet not controlled by a wall switch. • You might be too far from the base; move closer. • You might have too many extension phones on your telephone line to allow all of them to ring. Try unplugging some of them. 20 IN CASE OF DIFFICULTY 1450_book_1ATT 3/26 3/26/02 4:59 PM Page 21 1450_book_1ATT 3/26 3/26/02 4:59 PM Page 21 If you hear noise or interference when using the phone: • Make sure the base antenna is fully upright. • You may be out of range. Move c...
)
Iniciar sesión: