Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
For best performance, keep the base antenna fully upright. If you receive a call while you are out of range, the handset might not ring — or if it does ring, the call might not connect when you press PHONE. Move closer to the base, then press PHONE to answer the call. If you move out of range during a phone conversation, you might hear noise or interference. To improve reception, move closer to the base. If you move out of range without pressing OFF, your phone will be left “off the hook.” To hang up properly, walk back toward the telephone base, periodically pressing OFF until the call is disconnected. 5 91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 .U.. 07:21 Page 6 Getting Started Telephone base installation Install the telephone base as shown below. Choose a location away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. NOTE: Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. Be sure to use an electrical outlet not controlled by a wall switch. Plug power cord transformer into electrical outlet Plug long line cord into telephone jack 6 91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 .U.. 07:21 Page 7 Getting Started Battery installation & charging After installation, place the handset in the base and allow the battery to charge for 12 hours before use. You can keep the battery charged by returning the handset to the base after each use. When battery power is fully depleted, a full recharge takes about 8 hours. Charging light will be illuminated while battery is charging. Rotate antenna to fully upright position Place handset in base to charge for 12 hours before first use. Plug in battery here Low battery indicator Return handset to base to recharge when this symbol appears. (Handset will beep when battery is low.) NEW 00 OLD 27 8/12 10:06 AM Press coin into slot on base of handset to release latch, then remove cover To replace cover: 1 Insert tabs at top of cover into slots on base 2 Align tab at bottom of cover with slot in base, then press to click in place 7 91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 .U.. 07:21 Page 8 Getting Started Wall mounting The telephone base can be installed on any standard wall-phone outlet as shown below. Choose a location away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. Connect line cord and AC adapter as shown on page 6, then press notch and Plug power cord transformer into electrical outlet Press and slide down firmly so base is held securely on outlet mounting pegs Plug short line cord into telephone jack pull to open hinged wall mount Swivel wall mount down and lock in place 8 91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 .U.. 07:21 Page 9 Getting Started Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap) 9 91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 .U.. 07:21 Page 10 Press PROG to begin programming Press ^ or V to display features one by one Press SELECT to modify a displayed feature Telephone Operation Customizing your telephone Follow the steps below to program the telephone. To stop at any time, press OFF. If the phone rings, programming stops automatically so you may answer the call. Choose ringer sound 1 Press PROG to begin programming. 2 Press ^ until screen displays RINGER & setting. 3 Press SELECT to change current setting: RINGER: 1 Default setting: 1 4 Press ^ to display 1, 2, 3, 4 or OFF. You will hear a sample of each ringing type. 5 Press SELECT to select displayed ringing type and exit. Set handset display date and time 1 Press PROG to begin programming. To stop at any time, press OFF 2 Press ^ until screen displays DATE/TIME. 3 Press SELECT to view or change date and time: DATE/TIME Default setting: 1/01 12:00 AM 1/01 12:00 AM 4 Press ^ or V to change month, then press SELECT. 5 Repeat Step 4 to set day, hour, minute, and AM/PM. 6 Press SELECT to save selection and exit. NOTE: You can choose to set the time manually, or you can allow it to be set automatically with incoming Caller ID information. The time will be set automatically only if you subscribe to Caller ID service provided by your local telephone company (see page 5). 10 91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 .U.. 07:21 Page 11 Telephone Operation Customizing your telephone Choose dial mode 1 Press PROG to begin programming. 2 Press ^ until screen displays DIAL MODE & setting. 3 Press SELECT to change current setting: DIAL MODE: TONE Default setting: Tone 4 Press ^ to display TONE or PULSE. 5 Pres...