Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
(It may feel warm during use. This is normal.) • If you connect a reserve telephone on the same line, see page 19. 7 Preparation .. . •_• • Setting Up Battery Charge Place the handset on the base unit for about 15 hours. • The IN USE/CHARGE indicator lights. Recharge When the TALK/BATT LOW indicator flashes slowly or the unit beeps intermittently, recharge the battery. If you do not want to wait until the battery is fully recharged, we recommend you purchase an optional spare battery (page 16). eeo. Standard battery life If your Panasonic battery is fully charged; While in use (TALK) Up to about 4.5 hours While not in use (Stand-By) Up to about 14 days • Battery life may vary depending on usage conditions and ambient temperature. • Clean the handset and the base unit charge contacts with a dry soft cloth once a month, or the battery may not charge properly. • Once the battery is fully charged, you do not have to place the handset on the base unit until the TALK/BATT LOW indicator flashes slowly. • The battery cannot be overcharged. Wall Mounting This unit can be mounted on a wall phone plate. Pull down the handset hook so the tab holds the handset. Connect the AC adaptor. Tuck the telephone line cord inside the wall mounting adaptor, then push it in the direction of the arrow. • The word “UP” should face upward. Connect the telephone line cord. Mount the unit, then slide down. • Raise the antenna. To charge the handset battery: Place the handset on the handset hook as shown. • The IN USE/CHARGE indicator lights. 9 Preparation Making Calls 1 Press ITALKI • The TALK/BATT LOW indicator lights Dial a telephone number • If you misdial, press I FLASH I firmly then dial again To hang up, press I TALK I or place the handset on the base unit • The indicator light goes out TALK/BATT LOW Indicator (TALK • If an alarm tone sounds in step 1, move toward the base unit or place the handset on the base unit Then try again To redial the last number Press ITALKI ■» iREDIAL/PAUSEl To select the receiver volume HIGH or NORMAL (preset) Press I VOLUME/RINGER I while speaking • Each time you press, the volume level will change If noise interferes with the conversation Press (ch] to select a clear channel or move closer to the base unit 10 Answering Calls If the handset is off the base unit, press I TALK I. • You can also answer a call by pressing any dialing button 0 to 9, *, or # (— Any Key Talk). OR If on the base unit, just lift it. Adjusting the ringer volume Be sure the TALK/BATT LOW indicator light is off. • To select HIGH (preset) or LOW, press I volume/ringer] . (Each time you press, the ringer volume will change.) • To turn the ringer OFF, while pressing I VOLUME/RINGER I, press [§) until 2 beeps sound. • To turn the ringer ON, press [ VOLUME/RING ERl. The ringer sounds at the HIGH level. Selecting the ringer tone (2 types) When the TALK/BATT LOW indicator light is off, press [ VOLUME/RINGER I then press (*) within 5 seconds. The selected ringer tone sounds. 11 Basic Operation Automatic Dialing Storing Phone Numbers in Memory You can store up to 10 phone numbers in memory stations of the handset The dialing buttons (0 to 9) function as memory stations The TALK/BATT LOW indicator light must be off Press I PROGRAM! • The TALK/BATT LOW indicator flashes Enter a phone number up to 16 digits • If you misdial, press I PROGRAM! to end storing, then restart from step 1 Press I auto) Press a memory station number {0 to 9) • A confirmation tone sounds (See below) • To store other numbers, repeat steps 1 through 4 TALK/ ВАТТ LOW Indicator Memory Station Number (<-NPjJ What the confirmation tone means 1 beep The new number is stored 2 beeps The number is the same as a previously stored one 12 To erase a stored number Press I program] [AUTOl ^ the memory station number {for the phone number to be erased). Memory sticker Use the included memory sticker as a name or phone number index for automatic dialing. Attach the sticker to the unit or in a convenient place. ffífáhrÁïimàm ;? t 6 Г 7 k ft 3 a U 4 4 9 ; ¿ 5 о Ы ....... Dialing a Stored Number 1 Press [TALK], Press I AUTOL Press the memory station number (0 to 9). • The stored number is dialed. TALK Memory Station Number 13 Basic Operation Special Features One-Touch Dialing You can store a phone number in the DIRECT button The stored number is dialed with a one-touch operation To store a phone number in memory 1 Press I PROGRAM! when the TALK/BATT LOW indicator light is off • The indicator starts to flash 2 Enter a phone number up to 16 digits • If you misdial, press I program!, then restart from step 1 3 Press I DIRECT! • A confirmation tone sounds (See page 12) To dial a stored number 1 Press I TALK! 2 Press !DIRECT) • The stored number is dialed • To erase a stored number; Press I PROGRAM! ^ I DIRECT I Handset Locator From the base unit you can locate...