Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
See page 28. What the line indicator means Off The line is free. On You are using the line on the handset or the base unit. Flashing twice every 2 seconds Someone else is using the line on the handset, base unit or parallel connected telephone. Flashing A call is on hold. Flashing quickly A call is being received. Lighted handset keypad The handset dialing buttons will light while dialing and flash when a call is received. The lights will go out about 10 seconds after dialing or answering a call. 18 C=> With the Base Unit The unit will automatically select an idle line when you press ISP-PHONE to make a call. (To change the line selection, see page 36.) Press ISP-PHONE I. © The SP-PHONE indicator and the selected line indicator light. Dial a telephone number. o If you misdial, press I FLASH) firmly then dial again. When the other party answers, talk into the MIC (microphone). To hang up, press ISP-PHONEJ. » The indicator lights go out. © In step 1, you may select a line manually by pressing the line button instead of ISP-PHONE I. To adjust the speaker volume (12 levels) while talking To increase, press VOLUME [a). To decrease, press VOLUME Pvl. During the speakerphone operation: © For best performance, talk alternately with the caller in a quiet room. If the caller complains that your voice is hard to hear, press VOLUME [v) to decrease the speaker volume. © If the handset is on the base unit, you may switch to the handset by lifting it up. o The line indicator shows the line condition (p. 18). 19 c=> Making Calls To redial the last number dialed on the base unit Press ISP-PHONEI {or a line button) c> IREDlALl. To put a call on hold Press IHOLD). ® The SP-PHONE indicator light goes out and the line indicator flashes, o After 6 minutes, warning tones will sound every 10-15 seconds. After a total of 10 minutes, the call will be disconnected. To release the hold Press the line button. 0 If another phone is connected on the same line (p. 38), you can also release the hold by lifting its handset. 1 You may make or answer a second call on the other line while keeping , the present call on hold. See page 29. 20 Answering Calls When a call is being received, the called line indicator flashes quickly. The line is automatically selected when you answer the call. {To change the line selection, see page 36.) With the Handset If the handset is off the base unit, press I TALK I. ® The called line indicator lights. © You can also answer a call by pressing any dialing button O to (9), ©, or (g (— Any Key Talk). OR If on the base unit, just lift up. o The called line indicator lights. With the Base Unit ■j Press ISP-PHONEI. « The SP-PHONE indicator and the called line indicator light. 2 Talk into the MIC. 0 To hang up, press I SP-PHONE I. « The indicator lights go out. Line Indicators ! I SP-PHONE 1 Mic an£^ lnc*'ca*or 21 Speed] Dialler (Handset) Storing Phone Numbers in Memory You can store up to 10 phone numbers in the handset. The dialing buttons (® to O) function as memory stations. The TALK indicator light must be off before programming. Press IprogramI. o The TALK indicator flashes. Enter a phone number up to 16 digits. o If you misdial, press IPROGRAMI to end storing, then start from step 1. 3 4 Press I auto I. Press a memory station number ((o) to (9]). o A confirmation tone sounds.* © To store other numbers, repeat steps 1 through 4. 0 If a pause is required for dialing, [REPlAUPAUSEl can be stored in a phone number counting as one digit (p. 34). *What the confirmation tone means 1 beep: The new number is stored. 2 beeps: The number is the same as the previously stored one. 22 To erase a stored number Press IPROGRAMI c> | AUTO] c> the memory station number ((o] to [£]) for the phone number to be erased. Dialing a Stored Number 1 Press I TALK I. 2 3 Press I AUTOl. Press the memory station number (® to ID). * The stored number is dialed. o Numbers stored in the handset can only be dialed by the handset. Speed Dialer (Bas© Unit) Storing Phone Numbers in Memory You can store up to 10 numbers in the base unit. The dialing buttons ((o] to (9)) function as memory stations. The SP-PHONE indicator light must be off. Press [PROGRAM!- oThe IN USE/CHARGE indicator flashes. Enter a phone number up to 16 digits. © If you misdial, press [PROGRAM] to end storing, then start from step 1. Memory Station Numbers Press ÍAUTQ]. Press a memory station number ((0] to (9)). o A confirmation tone sounds.* ° To store other numbers, repeat steps 1 through 4. IN USE/CHARGE Indicator 0 If a pause is required for dialing, I PAUSE I can be stored in a phone number counting as one digit (p. 34). *What the confirmation tone means 1 beep: The new number is stored. 2 beeps: The number is the same as the previously stored one. 24 To erase a stored number Press I program! e> | AUTO I the memory station number ((o] to ®) for the phone number to...