Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
To set “9:30”, enter “0930”.) • The entered number is displayed. C Press (*) to select “AM" or “PM”. Press® repeatedly to set the day. 0 When finished, press [PROGRAM!. • The unit announces the time/day. The clock starts working. TALK/ ВАТТ LOW Indicator [SCREEN/PLAYBACK I and Indicator In step 4, you cannot enter numbers greater than 12. (To set “13:00”, enter “0100” and select “PM” by pressing®.) The accuracy of the clock is approximately ±45 seconds a month at room temperature. 16 To check the time/day Press IPR0GRAM1 +> I SCREEN/PLAYBACK I The current time/day is heard. When finished, press IPROGRAMI. Selecting the Caller’s Recording Time You may select the caller’s recording time as either "1 minute", “unlimited’ or “greeting only”. The factory preset is “unlimited”. Press IPROGRAMI. • The TALK/BATT LOW indicator flashes. Press I SCREEN/PLAYBACK I. • The indicator lights. • “P” is displayed on the base unit. Press (5). • The current setting is displayed. 1: 1 minute 2: unlimited 3: greeting only Press (T), (2) or (3j to select the recording time. • The setting is displayed. When finished, presslPROGRAMl. • The indicator lights go out. TALK/ ВАТТ LOW Indicator I SCREEN/PLAYBACK and Indicator If you select “greeting only”, the unit answers a call with the greeting message, then hangs up. The unit will not record any messages. 17 ^ Programmable Preparations Selecting the Number of Rings You may select the number of rings before the answering system answers a call, from “1 ” to “7” or “AUTO (for Toll Saver)”. The factory preset is “AUTO”. Press iPROGRAMl The TALK/BATT LOW indicator flashes. 2 Press I SCREEN/PLAYBACK!. • The indicator lights. • “P” is displayed on the base unit. 2 Press(2). • The current setting is displayed. A Press a dialing button (g to @ to * set the number of rings. 0: Selects “AUTO”. “A” is displayed. 1-7: The unit will answer on the selected number of rings. When finished, presslPROGRAMl. • The indicator lights go out. TALK/ ВАТТ LOW Indicator I PROGRAM}— С I SCREEN/PLAYBACK] and Indicator Toll Saver (When set to “AUTO”) When you call the unit from a touch tone telephone: If the unit answers on the 2nd ring; there is at least one new message. If the unit answers on the 4th ring; there are no new messages. Hang up when you hear the 3rd ring. This will save you the toll charge for the call. 18 Setting the CPC (Calling Party Control) Function The CPC function is preset to “A”. If you use a call waiting service, set to “b", or the call waiting tone will disconnect someone leaving a message. 1. Press [PROGRAM]. 2. Press ISCREEN/PLAYBACKl. 3. Press (3). • The current setting “A” or "b" is displayed on the base unit. 4. To select “b”, press (2}. OR To select “A”, press®. • The setting is displayed. 5. When finished, pressIPROGRAMI. Setting the Greeting Monitor Function When your greeting message is being played to the caller, you can also listen to it through the speaker. To listen to your greeting, set to “2 (ON)". The factory preset is “1 (OFF)”. 1. Press IPROGRAMI. 2. Press I SCREEN/PLAYBACKl. 3. Press (4). • The current setting "1 ” or “2” is displayed on the base unit. 4. To set to “2 (ON)", press (2). OR To set to “1 (OFF)”, press (T). • The setting is displayed. 5. When finished, press IPROGRAMI. 19 Preparation Making Calls 1 Press iTALKl. • The TALK/BATT LOW indicator lights. Dial a telephone number. • If you misdial, press I FLASH!firmly then dial again. To hang up, press I talk I or place the handset on the base unit. • The indicator light goes out. • If an alarm tone sounds in step 1, move toward the base unit or place the handset on the base unit. Then try again. To redial the last number Press I TALK I * iREDIAL/PAUSEl. To select the receiver volume HIGH or NORMAL (preset) Press I VOLUME I while talking. • Each time you press, the volume level will change. If noise interferes with the conversation Press fCHl to select a clear channel or move closer to the base unit. 20 Answering Calls With the Handset If the handset is off the base unit, press [TALKI. • You can also answer a call by pressing any dialing button 0 to 9, *, or # (— Any Key Talk). OR If on the base unit, just lift it. Adjusting the ringer volume Be sure the TALK/BATT LOW indicator light is off. • To select HIGH (preset) or LOW, press I RINGER I. (Each time you press, the ringer volume will change.) \ • To turn the ringer OFF, while pressing I RINGER I, press® until 2 beeps sound. • To turn the ringer ON, press I RINGER I. The ringer sounds at the HIGH level. 21 Cordless Telephone Answering Calls With the Base Unit (Digital Speakerphone) -J Press I DIGITAL SP-PHQNEI • The indicator lights O Speak into the MIC (microphone) To hang up, press I DIGITAL ¿P^PHQNEl • The indicator light goes out • While using the speakerphone, if the handset is on the base unit, you may switch to the handset by li...