Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Mount the unit, then slide down. © Raise the antenna. To charge the handset battery: Place the handset on the handset hook as shown. ©The IN USE/CHARGE indicator lights. 45 ОрййооаО Spare Battery When the handset battery needs charging, replace it with a fully charged optional spare battery. This eliminates having to wait for the handset battery to recharge. Please purchase a Panasonic P-P592 (KX-A92) battery and install it in the base unit to charge. Installing the spare battery in the base unit The spare battery is always being charged in the base unit while the AC adaptor is connected. The battery cannot be overcharged. Attention: The product you have purchased is powered by a nickel 1 Open the cradle cover by pushing the tab and lifting the cover. 2 Install the spare battery as shown observing the proper polarity, then close the cradle cover. SPARE CHARGE Indicator » The SPARE CHARGE indicator lights. cadmium battery which is recyclable. At the end of its useful life, under various state and local laws, it is illegal to dispose of this battery into your municipal waste stream. Please call 1-800-8-BATTERY for information on how to recycle this battery. 46 Replacing the handset battery with the spare battery To prevent memory loss, replace within 5 minutes. Remove the handset cover, then remove the battery. > Replace the handset battery with the spare battery in the base unit. © Remove the spare battery. (¿) Insert the handset battery in the base unit observing the proper polarity. Install the spare battery in the handset observing the proper polarity. © When finished, close the handset cover. © If the TALK/BATT LOW indicator flashes slowly even when the handset battery has been fully charged, it is time to change the battery with a new one. Remember to fully charge the new battery after battery replacement. © Please use only a Panasonic P-P592 (KX-A92) battery. For accessory order, call 1-800-332-5368. Before Requesting HI0lip Cordless telephone Problem Remedy An alarm tone sounds when © You are too far from the base unit, you press I TALK I. Move closer and try again. ISCREEN/PLAYBACklor <> Place the handset on the base unit I INTERCOM I. and try again. © Plug in the AC adaptor. © Move closer to the base unit quickly, or the call will be terminated within 60 seconds. © Plug in the AC adaptor. © Set the handset and the base unit away from electrical appliances, o Move closer to the base unit. © Raise the base unit antenna. 0 Press (CH] to change the channel. The handset does not ring. © The ringer volume is set to OFF. Press I ringer I when the TALK/BATT LOW indicator light is off. The base unit does not ring. © The RINGER selector is set to OFF. Set to HIGH or LOW. © You cannot store a number while the unit is in the talk or intercom mode. © Do not pause for over 30 seconds while storing. While storing a phone number, © To answer the call, press I TALK I or the unit starts to ring. ISP-PHONEI. The program will be canceled; store the number again. I LOCATOR/lNTERCOMi does © The handset is too far from the base not function. unit or is engaged in an outside call. I REDIAL/PAUSE I does not © It will redial the last number dialed if function properly. pressed at the outset of a call (p. 20). If another number has been dialed first, it will operate as a pause button (p. 28). You cannot store a phone number in memory. An alarm tone sounds continuously while using the handset. Static, sound cuts in/out, fades. Interference from other electrical units. 48 Answering system Problem The answering system is on, but no incoming messages are recorded. “ ” is displayed and no incoming messages are recorded. Some incoming messages have not been recorded up to the end. You cannot operate the answering system at the base unit. You cannot operate the answering system from a touch tone phone. You cannot operate the answering system with the handset. >=> Remedy © The recording time is set to “greeting only”. Select “1 minute” or “unlimited” (P- 17). © The memory is full. Erase some or all messages (p. 31). © The memory is full. Erase some or ail messages (p. 31). If “ J ” is still displayed, erase your greeting message and re-record a shorter greeting (p. 13, 14). © Set the CPC function to “b” (p. 19). © The handset user is operating the answering system. Wait until the IN USE/CHARGE indicator light goes out. © Be sure to press the correct remote code. © The answering system may not respond if the phone produces tones that are too short to activate the unit. Press each button firmly. © The answering system is off. Turn it on (p. 39). © Someone is operating the answering system. © You are too far from the base unit. Move closer to the base unit. □=> Before Requesting Help General Problem Remedy The unit does not work. © Check the setting (p. 10-12). © Charge the battery fully. © Clean the charge contacts and charge again. © Place the handset on t...