Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Ex. “Press Mute.” indicates “Press the soft key below MuteL”. • The navigator key is indicated by the arrows [d] or [B]. Preparation For assistance, please call: 1-800-211-PANA(7262) Installation Connections Fasten the AC adaptor cord. Single-Line Telephone Jack (RJ11C) Telephone Line Cord Power Outlet (AC 120 V, 60 Hz) AC Adaptor Hooks • USE ONLY WITH Panasonic AC ADAPTOR PQLV1 (Order No. PQLV1Z). • The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) • If your unit is connected to a PBX which does not support Caller ID and voice mail services, you cannot access those services. • The unit will not work during a power failure. We recommend connecting a standard telephone to the same telephone line or to the same telephone jack using the Panasonic KX-J66 T-adaptor. Preparation For assistance, please call: 1-800-211-PANA(7262) 9 Installation Installing the Battery in the Handset Insert the battery (1), and press it down until it snaps into the compartment (2). Close the cover. To replace the battery: Press the notch on the cover firmly and slide it as indicated by the arrow. Replace the old battery with a new one (p. 10). Close the cover and charge the battery for 6 hours. Battery Charge Place the handset on the base unit. Charge for 6 hours before initial use. • The unit beeps once, the CHARGE indicator lights, and “Charging” is displayed. • When the battery is fully charged, “Charge completed” is displayed. Battery strength You can confirm battery strength on the handset display. Battery strength is indicated by the icons shown in the chart to the right. Display prompt Battery strength 5 Fully charged 6 Medium 7 Low 074 (flashing) Needs to be recharged. 8 Discharged 1 2 OR CHARGE Indicator Installation Recharge Recharge the battery when: —“Recharge battery” is displayed on the handset, —“7” flashes, or —the handset beeps intermittently while it is in use. Recharge battery • The display will continually indicate “Recharge battery” and/or “7” will flash when the handset battery is charged for less than 15 minutes and the handset is lifted off the base unit. • If the battery has been discharged, the handset will display “Charge for 6h” and “8” when you place the handset on the base unit. The handset will not work unless the battery is charged. Continue charging. Battery replacement: If you cleaned the charge contacts and fully charged the battery, but after a few telephone calls, “Recharge battery” is displayed and/or “7” continues to flash, or “Charge for 6h” and “8” are displayed, the battery may need to be replaced. Please order a new Panasonic HHR-P104 battery at the telephone number shown on page 2. To replace the battery, see page 9. A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery. Battery information After your Panasonic battery is fully charged, you can expect the following performance: Operation Operating time While in use (TALK) Up to 5 hours While not in use (Standby) Up to 11 days • A fully charged battery will give you up to 5 hours of continuous talk time, or keep your handset in Standby mode to receive incoming calls for up to 11 days (if no phone calls are made). Battery power is consumed whenever the handset is off of the base unit, even when the handset is not in use. The longer you leave the handset off of the base unit, the time you can actually talk on the handset will be shortened. Actual battery performance depends on a combination of how often the handset is in TALK mode and how often it is in Standby mode. • If the battery is fully charged, you do not have to place the handset on the base unit until “Recharge battery” is displayed and/or “7” flashes. This will maximize the battery life. • If you want to keep the battery fully charged at all times, place the handset on the base unit when the handset is not used. The battery cannot be overcharged. • Clean the charge contacts of the handset and the base unit with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly. Programmable Settings Programming Guidelines Handset This unit has several programmable functions which can be selected from the function menu on the display (p. 12). Back Select When “d” or “B” is displayed, navigator key scrolls through the menu. The soft keys selects the functions displayed above each soft key. [OFF] exits programming. [MENU] enters the function menu. How to select a function item from the menu Make sure the handset and base unit are not being used. The handset must be operated near the base unit and while off the base unit. 1 Press [MENU]. • The main menu is displayed (p. 12). 2 Scroll to the desired item by pressing [d] or [B]. Initial setting KBack dB Select L 3 Press Select to select the desired item. Back Select 4 If the item has a sub-me...