Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Panasonic Tamaño del archivo: 1.81 mb Nombre del archivo: KXTG8231.PDF Idioma del manual:

Registering a handset to a base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit (for example, w flashes even when the handset is near the base unit), register the handset. 1 {MENU} (center of joystick) i * i {SELECT} 2 {V}/{^}: “Registration” i {SELECT} 3 {V}/{^}: “HS registration” i {SELECT} 4 Base unit: Press and hold {x} (LOCATOR) for about 5 seconds, until the registration tone sounds. LIf all registered handsets start ringing, press {x} (LOCATOR) to stop, then repeat this step. LAfter pressing {x} (LOCATOR), the rest of this procedure must be completed within 1 minute and 30 seconds. 5 Handset: Press {OK}, then wait until a long beep sounds and w stops flashing. LWhen the handset has been registered successfully, w will stop flashing. If the key tone is turned on (page 28), a confirmation tone will be heard. Deregistering a handset A handset can cancel its own registration (or the registration of another handset) that is stored in the base unit. This will allow the handset to end its wireless connection with the system. 1 {MENU} (center of joystick) i * i {SELECT} 2 {V}/{^}: “Registration” i {SELECT} 3 {V}/{^}: “Deregistration” i {SELECT} 4 {3}{3}{5} i {OK} LThe numbers of all handsets registered to the base unit are displayed. 5 Select the handset(s) you want to cancel, by pressing the desired handset number ({1} – {6}). i {OK} LThe selected handset number(s) flashes. For assistance, please visit Multi-unit Operation LTo cancel a selected handset number, press the number again. The number stops flashing. 6 {V}/{^}: “Yes” i {SELECT} LA long beep will sound as each handset number disappears. 7 After “Deregistered” is displayed, press {OFF}. For assistance, please visit Useful Information Belt clip You can hang the handset on your belt or pocket using the supplied belt clip. To attach the belt clip To remove the belt clip Headset (optional) Connecting a headset to the handset allows hands-free phone conversations. We recommend using the Panasonic headset noted on page 4. LHeadset shown is KX-TCA86. For assistance, please visit Useful Information Error messages If the unit detects a problem, one of the following messages is shown on the display. Display message Cause/solution Busy LThe called handset is in use. LThe handset you are calling is too far from the base unit. LThere is no handset registered to the base unit matching the extension number you entered. LOther units are in use and the system is busy. Try again later. Error!! LRecording was too short. Try again. Failed LPhonebook copy failed. Confirm the other handset (the receiver) is in standby mode and try again. Incomplete LThe receiver’s phonebook memory is full. Erase the unnecessary phonebook entries from the other handset (the receiver) and try again. Memory full LThe handset’s phonebook memory is full. Erase unnecessary entries (page 20). Messages full LMessage memory becomes full. Erase unnecessary messages (page 31). No items stored LYour phonebook, caller list or redial list is empty. No link to base. Move closer to base, try again. LThe handset has lost communication with the base unit. Move closer to the base unit and try again. LUnplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again. LThe handset’s registration may have been canceled. Re-register the handset (page 38). Please lift up and try again. LA handset button was pressed while the handset was on the base unit or charger. Lift the handset and press the button again. You must first subscribe to Caller ID. LYou must subscribe to Caller ID service. Once you receive caller information after subscribing to Caller ID service, this message will not be displayed. For assistance, please visit Useful Information Troubleshooting If you still have difficulties after following the instructions in this section, disconnect the base unit AC adaptor, then reconnect the base unit AC adaptor. General use Problem Cause/solution The unit does not work. LMake sure the batteries are installed correctly and fully charged (page 12). LCheck the connections (page 11). LUnplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again. LThe handset has not been registered to the base unit. Register the handset (page 38). I cannot hear a dial tone. LThe base unit AC adaptor or telephone line cord is not connected. Check the connections. LIf you are using a splitter to connect the unit, remove the splitter and connect the unit to the wall socket directly. If the unit operates properly, check the splitter. LDisconnect the unit from the telephone line and connect a known working telephone. If the working telephone operates properly, contact our service personnel to have the unit repaired. If the working telephone does not operate properly, contact your service...

Descargar ahora

Introduzca dos números de la imagen: