Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
See step 5* and 6*. 5. Place siphon assembly in container of correct thinner, for the spray product being used,, and prime the pump as shown in step 13, of "Spraying". *See special notes from step 4. Allow thinner to circulate back into the container for a few minutes to flush the prime valve. 6. Close prime valve. 7. Trigger gun into paint container until thinner comes through. *See special notes from step 4. Re-direct flow into waste container and continue spraying until thinner runs clear. Heavily soiled thinners may have to be changed to complete cleaning job. 8. Lift siphon assembly and allow pump to run dry. 9. Repeat procedure using a gallon of H.E.R.O. Equipment Wonder Wash solution. If not using Wonder Wash, unit must not be stored with water. Only store with a non corrosive material ( Paint thinner, solvent ). 10. Switch unit "off" and trigger gun to relieve remaining pressure. 11. Remove and rinse gun handle filter in correct thinner. SPECIAL STORAGE INSTRUCTIONS In areas where the sprayer is NOT used 12 months of the year, special preparations must be used for winter or off season storage. Because solvents evaporate quickly, they should not be used for long term storage. A petroleum based solution ( solvent and oil ) should be used as an extended storage material. DO NOT allow storage solution to freeze in the sprayer. H.E.R.O. Equipment Wonder Wash, available from your H.E.R.O. distributor, will provide the added cleaning benefits of solvent at a much lower cost. Suitable as a short term ( 1-2 days ) storage solution only H.E.R.O. INDUSTRIES 8 Model 3000 Owner’s Manual SPECIAL NOTES AND INSTRUCTIONS NEVER LEAVE THE UNIT UNDER PRESSURE WHEN NOT SPRAYING (MOTOR TURNED OFF). RELIEVE PRESSURE BY TRIGGERING GUN. NEVER STORE THE UNIT WITH PAINT OR WATER IN THE PUMP SYSTEM, EVEN OVERNIGHT. NEVER attempt to start the motor when the unit is under pressure. Relieve pressure and follow instructions in "Setting up to spray" . NEVER attempt to run the motor on longer or lighter extension cord than specified. . Avoid operating the unit while tilted. Keeping it level assures greater operating efficiency. . If motor's thermal overload switch has opened, unplug unit and allow it to cool. . DO NOT attempt to resume spraying before determining and correcting the cause of overheating. . Always follow flushing and cleaning instructions exactly. . In hot weather, locate unit in shade. Regularly check the level of H.E.R.O. LVO hydraulic fluid in the hydraulic tank. It should be kept near full, top up as needed with only genuine H.E.R.O. LVO hydraulic fluid. Crankshaft eccentric bearing should be greased at regular intervals consistent with hours of use. Use MO-2 grease ( i.e. common auto grease) approximately every 10 hours of operation. If you wish to power your H.E.R.O. airless sprayer with a generator, it must be a minimum of a 4500 watt generator, in good operating condition. NOTE; An electric tool must be powered by a generator which has an output wattage of at least three times the maximum draw of the motor under full load. A minimum 50’ and a maximum of 300’ of airless spray hose may be used. NOTE: 50’ x 3/8” paint hose ( part # 117 ) should be used for every 50’ x 1/4” paint hose ( part # 114 ) over 100’. 100’ total length of paint hose = 2 of 50’ x 1/4” paint hose. 150’ total length of paint hose = 2 of 50’ x 1/4” paint hose and 1 of 50’ x 3/8 paint hose. 200’ total length of paint hose = 2 of 50’ x 1/4” paint hose and 2 of 50’ x 3/8 paint hose. 250’ total length of paint hose = 3 of 50’ x 1/4” paint hose and 2 of 50’ x 3/8 paint hose. 300’ total length of paint hose = 3 of 50’ x 1/4” paint hose and 3 of 50’ x 3/8 paint hose. Product viscosity, altitude ( feet above sea level ) and vertical reach can effect pump performance and special accessories may be required. Product viscosity may have to be further reduced at higher elevations. Special “ High Altitude” siphon assemblies ( part # 4-210-HA ) are available for use in areas at or above 5000 feet above sea level. This kit may also prove beneficial if spraying thicker viscosity materials. The larger diameter 3/8” paint hose should also be used. . Check drive belt ( part # 66/100 ) tension frequently. The belt will stretch with use, and should be adjusted after 20 hours of operation and again after 50 hours. Periodic checks after 50 hours should be made. Failure of the drive belt is not covered by the equipment warranty, so proper maintenance of the belt is important. . Regularly check fittings, bolts, nuts and connections for damage. Tighten, adjust or replace as required. . Check crankshaft alignment often. An out of alignment crankshaft will cause the damage to the eccentric bearing. H.E.R.O. INDUSTRIES 9 Model 3000 Owner’s Manual AIRLESS SPRAY PAINTING SUGGESTIONS AND TECHNIQUE A good airless spray application is the result of many factors. Surface preparation, which includes cleaning and degreasing, priming, material compatibility, quality finish p...
Otros modelos de este manual:Armas - 3000 (1.01 mb)