Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Warning! Air may still be in the Spiral Air Hose (46) after turning off the unit. Always point the unit at scrap material or into a bucket and fire the unit after turning it off. Troubleshooting FIGURE 4 Problem Cause Solution The Paint Drips on -product too diluted - add undiluted product object to be painted - spray adjustment -slow sprayer movement - clogged gun - distance problem - reduce paint flow - faster sprayer movement - let go of Trigger when reversing - increase distance between gun and object Weak or irregular spray -product too diluted - spray adjustment -fast movement - gun clogged - gun distance - add undiluted product - increase paint flow - move slower - clean gun - increase distance between gun and object No Paint Coverage -product not diluted enough -paint too thick - gun clogged - hose broken - Filter (30) clogged - Grainy paint - Cup Cover (19) not closed - add thinner - check viscosity and adjust -clean gun -replace hose -replace filter -filter paint through cheesecloth - tightly close Cup Cover (19) SKU 91772 For technical questions, please call 1-800-444-3353. Page 12 Note: A small Inflator (32) accessory comes with this unit. To fill a raft or air mattress, attach the inflator as shown in FIGURE 2 on page 11. When the inflator is attached to the object being inflated, start the unit using the Switch (31). Turn off the unit when the object is inflated. Read the instruction manual of the object to be inflated to determine the recommended and maximum PSI for filling the object. You will have to check the air pressure of the object by using a separate air pressure gauge (not included). Do not overinflate. Overinflating may cause the object to explode. Note: A small Inflator (32) accessory comes with this unit. To fill a raft or air mattress, attach the inflator as shown in FIGURE 2 on page 11. When the inflator is attached to the object being inflated, start the unit using the Switch (31). Turn off the unit when the object is inflated. Read the instruction manual of the object to be inflated to determine the recommended and maximum PSI for filling the object. You will have to check the air pressure of the object by using a separate air pressure gauge (not included). Do not overinflate. Overinflating may cause the object to explode. G 1. WARNING! Make sure the Power Switch (31) of the Motor Unit is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect the general condition of the Sprayer. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. After each use, clean the gun immediately. Open the Cup Cover (19) and remove the Paint Cup (24). Replace left over paint in its container and seal the container. Pour small amounts of thinner into the Paint Cup (24) and replace the Cup Cover (19). Fire the Spray Gun into a paint waste receptacle until the thinner comes out completely clean. Repeat if necessary. Clean off any trace of paint from the Spray Gun. Clean off the Gasket (20) that is under the Cup Cover (19). 4. Clean the Fluid Nozzle (15) and the Fluid Needle (4). First, unlock and remove the Lock Ring (17), and Fluid Tip (16). Completely loosen the Fluid Needle Screw (1). Remove the Needle Spring (2) and push out the Fluid Needle (4). Do not use tools as they will bend the part. Put the parts in a container with thinner and clean them. Replace them in the proper order. Refer to the Assembly Drawing on page 15. 5. Run water through the Spiral Air Hose (46) making sure it is clean inside. Disconnect the Spiral Air Hose from spray gun or inflator and the motor unit, then allow it to dry before reassembly. 6. Make sure the Gasket (20) on the Paint Cup (24) is not torn or broken. If it is, replace it immediately. Always make sure the Gasket (20) is on correctly. SKU 91772 For technical questions, please call 1-800-444-3353. Page 13 PARTS LIST Part Description Qty. Part Description Qty. 1 Fluid Needle Screw 1 24 Paint Cup 1 2 Needle Spring 1 25 Trigger 1 3 Washer 1 26 Handle O-ring 2 4 Fluid Needle 1 27 Gun Body 1 5 Needle Cover 1 28 Strap 1 6 Needle Sealing Thread 1 29 Exhaust Cover 1 7 Gasket 2 30 Filter 1 8 Bolt 1 31 Switch 2 9 Plug 1 32 Inflator 1 10 Washer 1 33 Viscosity Cup 1 11 Pin 1 34 Cord 1 12 Washer 1 35 Pin Board 1 13 Sealing Thread Head 1 36 Front Turbine Shell Pin 1 14 Sealing Ring Head 1 37 Back Turbine Shell Pin 1 15 Fluid Nozzle 1 38 Fixed Turbine Pin 8 16 Fluid Tip 1 39 Left Turbine Shell 1 17 Lock Ring 1 40 Pad 7 18 Vent 1 41 Gun Tray 1 19 Cup Cover 1 42 Turbine O-ring 1 20 Gasket 1 43 Turbine 1 21 Inner Cover 1 44 Right Turbine Shell 1 22 Hex Thread 1 45 Combined Gun Body 1 23 Material Tube 1 46 Spiral Air Hose 1 ...
Otros modelos de este manual:Armas - 91772 (835.13 kb)