Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
Use two wrenches (one on the swivel (8) and one on the hose), to tighten all connections securely. 3. Refer to sprayer instruction manual for priming instructions. Installing Tip (26) and Guard (25) on Gun WARNING 1.If equipment has recently been operated, relieve pressure. Set trigger lock (2). 2.Using a pencil or similar object, insert seal (24) into back of guard (25). 3. Install guard (25) over end of gun (1). 4. Insert tip (26) in guard (25). Tighten retaining nut. Operation Spraying 1. Unlock trigger lock (2). 2. Be sure the arrow shaped tip (26) faces forward (spray). 3. Hold gun perpendicular and approximately 12-inches (304 mm) from surface. Move gun first, then pull gun trigger (13) to spray a test pattern. 4. Slowly increase pump pressure until coverage is uniform and even (see sprayer instruction manual for additional information). Aligning Spray WARNING 1.Relieve pressure. Set trigger lock (2). 2. Loosen guard (3) Horizontal (4) Vertical retaining nut. 3. Align guard (25) horizontally to spray a horizontal pattern. 4. Align guard (25) vertically to spray ti9535b ti9535b a vertical pattern. Clearing Clogs WARNING 1. Relieve pressure. Set trigger lock (2). 2. Rotate tip (26) 180°. Unlock trigger lock (2). Trigger gun into pail or onto ground to remove clog. 3. Set trigger lock (2). Rotate tip (26) 180° back to spray position. Cleanup Flush gun after each work shift and store in a dry location. Do not leave the gun or any parts in water or cleaning solvents. 311861E Parts 1 14 8 11 19 5 7a 13 15b ti8502b 22 20 21 9 10 31 16/17 7b (see page 4) 6 12 15a 2 Ref Ref No. Part. No. Description Qty No. Part. No. Description Qty 15J768 TRIGGER, Contractor Gun, 4-finger 1 1 288812 HOUSING, assy., Contractor 1 289914 HOUSING, assy., FTX 1 (not shown) 5 287032 FILTER, 60 mesh 1 15J769 TRIGGER, FTX Gun, 4-finger (not 1 287033 FILTER, 100 mesh 1 shown) 287034 FILTER, 60 and 100 mesh combo 1 14 117602 SCREW, shoulder, pan hd 2 6 120777 PACKING, o-ring 1 15 288488 KIT, needle, repair 1 7 HANDLE 1 15a NEEDLE, assembly 1 7a 15K282 Contractor Gun 1 15b DIFFUSER, assembly 1 7b 15J735 FTX Gun 1 16 15J696 PIN, trigger (page 4) 1 15J736 FTX-A Gun (not shown) 1 17 105334 NUT, lock, hex (page 4) 1 8 288811 SWIVEL, assy, gun 1 19 15J464 GUARD, trigger 1 9 120733 O-RING, urethane, clear 1 20 15J528 GUIDE, spring 1 10 15J706 RETAINER, guard, trigger 1 21 121093 SPRING, compression 1 11 15J698 TUBE, handle, Contractor Gun 1 22 15B549 NUT, end 1 12 120834 SCREW, set, Contractor Gun 1 31 119799 BRUSH, cleaning 1 13 15J409 TRIGGER, Contractor Gun 1 Tip and Guard Ref 24 No. Part. No. Description Qty RAC 5 24 246453 OneSeal™, RAC X (5-pack) 1 243281 OneSeal™, RAC 5 (5-pack) 1 25 246215 GUARD, RAC X 1 243161 GUARD, RAC 5 1 26 LTX515 TIP, spray 515, RAC X 1 LTX517 TIP, spray 517, RAC X 1 286515 TIP, spray 515, RAC 5 1 286517 TIP, 517, RAC 5 1 PAA517 TIP, spray, latex, RAC X (517), Europe 1 RAC X 25 26 24 ti8505a 2625 _ 311861E Maintenance WARNING WARNING 1.Relieve pressure. Set trigger lock (2). Before performing any maintenance on gun, read all warnings on front cover of this manual and relieve pressure. 2. Remove tip (26) and guard (25) from gun (1). Cleaning/Replacing Filter (5) 3. Disconnect fluid hose from gun at swivel (8). 4. Remove nut (17) and trigger pin (16). 1.Relieve pressure. Set trigger lock (2) 5. Unscrew diffuser (15a) from front of gun (1). 6. Remove needle assembly (15b) through front of gun (1). 7. Use a soft brush to clean out internal passages of gun. 2. Disconnect fluid hose from gun at swivel (8). 8. Grease o-rings of new needle using a non-silicon grease. 3. Disconnect trigger guard (19) from guard retainer (10). 9. Guide new needle (15b) through front of gun (1) making 4. Unscrew handle (7) from gun (1). sure the flat sides (a) of the needle assembly face the 5. Remove filter (5) through top of handle (7). sides of gun housing. 6. Clean filter (5). Use a soft brush to loosen and remove 10. Install diffuser (15a). Torque diffuser to 26-30 ft-lbs excess debris. (35.25 - 43.38 N•m). 7. Insert clean filter (5) into handle (7). 11. Replace pin (16) and nut (17). 8. Reattach handle (7) to gun (1). Tighten securely. 9. Reconnect trigger guard (19) to guard retainer (10). Translated Manuals Repair Tools needed: • 8-inch adjustable wrench • 1/4-inch nut driver Replacing Needle Spanish - 312098 Estonian - 312277 French - 312099 Latvian - 312278 Dutch - 312265 Lithuanian - 312279 German - 312266 Polish - 312280 Italian - 312267 Hungarian - 312281 Turkish - 312268 Czech - 312282 Greek - 312269 Slovakian - 312283 Croatian - 312270 Slovenian - 312284 Portuguese - 312271 Romanian - 312285 Danish - 312272 Bulgarian - 312286 Finnish - 312273 Chinese - 312287 Swedish - 312274 Japanese - 312288 Norwegian - 312275 Korean - 312289 Russian - 312276 Translated manuals can be requested through a distributor or at Technical Data Maximum working pressure 3600 psi (248 bar, 24.8 MPa) Fluid orifice size 0.125 in. (3.18 ...