Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com Web Site: We are proud to offer the Grizzly Model H7670 HVLP Spray Gun. This model is part of a growing Grizzly family of fine tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation, and proof of Grizzly’s commitment to customer satisfaction. The Model H7670 is designed to be used for smaller jobs where large volumes of material are not needed. The Model H7670 features HVLP technology, which has greater transfer efficiency than suction feed spray guns and reduces overspray, saving on material costs. It is our pleasure to provide this manual with the Model H7670. It was written to encourage safety considerations and guide you through general operating procedures and maintenance. The specifications, details, and photographs in this manual represent the Model H7670 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Read the manual before operation. Become familiar with this spray gun, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed. Foreword Contact Info Tool Data Type ............................. HVLP Gravity Feed Fluid Tip .......................................... 0.8 mm Air Consumption ...............................6 CFM Inlet Air Pressure ........3-4 Bar /43.5-58 PSI Fluid Pressure ............................... >10 PSI Maximum Pattern Width ................ 190 mm Material Capacity ................. 100 ml / 4 fl oz SECTION 3: SET UP Unpacking Your spray gun left our warehouse in a carefully packed box. If you discover the spray gun is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condition of the shipment, you should inventory the equipment. Inventory After you have unpacked the carton you should find the following: Model H7670 Inventory (Figure 1) A. Spray Gun ......................................... 1 B. Cup 100 ml ........................................ 1 C. Cleaning Brush .................................. 1 D. Service Wrench.................................. 1 E. Filters ................................................. 2 F. Barbed Hose Fitting ........................... 1 G. Lock Nut............................................. 1 H. Gauge ................................................ 1 Figure 1.Model H7670 inventory. H B C D G F E A -8-Model H7670 HVLP Spray Gun Assembly Controls 1. Insert the filter into the gun body (see 2. Screw the cup onto the top of the body. 3. Install the barbed hose fitting into the base of the gun handle and tighten in place with the lock nut. 4. Secure the air hose to the barbed fitting with a hose clamp. Note: Using a 1.4" NPS quick disconnect set-up (not included), will make operation and maintenance tasks easier. 5. Attach the spray gun to an air hose regulated between 43.5 and 58 PSI. Note: For the best results, use a hose that will be dedicated for spray use only. Do not use a hose that has been used with an in-line oiler or other possible contaminant. If you need additional help with this assembly, call our Technical Support at: (570) 546-9663. 1. Fluid Control: Controls the volume of material that travels through the fluid tip. 2. Pattern Control: Adjusts the spray pattern from a round pattern to a wide fan. 3. Air Flow Control: Controls the fluid pressure inside the spray gun. 4. Atomizing Cap: Controls the spray pattern from vertical to horizontal. 5. Trigger: Two stage trigger. Stage one only releases compressed air for blowing off the work piece. Stage two sprays material. 6. Cup: 100 ml metal cup allows for easy clean-up. Includes a vented cap. 7. Regulator/Gauge: Regulates inlet air pressure to the spray gun. It can be attached directly to the gun for on- the-spot air adjustments or directly from the air source. Note: DO NOT attach to an unregulated air source that exceeds 120 PSI. Figure 2. Installing filter. Figure 3. Controls. Figure 2). Cup Fluid Control Pattern Control Air Flow Control Atomizing Cap Trigger Regulator/Gauge Model H7670 HVLP Spray Gun -9 SECTION 4: OPERATIONS EXPLOSIONHAZARD!DONOTsmoke or have any source of flame or spark near spraying.Vapors will explode if ignited. RESPIRATORY HAZARD! Always use respirator rated for organic vaporand solvent use when using spray equipment. Failure to protect your lungs can lead to respiratory illness and nervous system damage. Spraying The Model H7670 HVLP...