Votos - 4, Puntuación media: 3
(
)
)
|
Resumen del manual
J Consult the sprayed medium manufacturer’s documentation for information about suitable thinners (water, solvents). 1. Thoroughly mix the unthinned sprayed medium and bring it to average room temperature (20-22°C). Do not increase the temperature to change the viscosity. 2. Add a suitable thinner. 3. Test the viscosity as described above (see Fig. C). NoTE: Never use nitro-thinners to thin synthetic resin paint! Example of DIN guidance material value Car body paint 16-20 DIN-sec Acrylic paint 25-30 DIN-sec Synthetic resin paint 25-30 DIN-sec Primer 25-30 DIN-sec Wood impregnation 25-30 DIN-sec Glaze 25-30 DIN-sec Hammer finish paint 30-35 DIN-sec* Emulsion paint 40-80 DIN-sec * This device cannot be used to spray media containing discrete particles/solids. The abrasive effect of these media shortens pump and valve life. Q Preparing the surface to be sprayed The surface to be sprayed must be clean, dry and free of grease. j j Roughen smooth surfaces and remove any abraded dust. Always cover the surrounding area around the surface to be sprayed. The spray cloud may contaminate the surrounding area. Q Bringing into use Q Selecting the nozzle Nozzle Use Nozzle, 0.6 mm all paints, varnishes Nozzle, 0.8 mm thick-flowing sprayed media Cleaning nozzle a thinner, harder spray for spot-cleaning of surfaces Nozzle extension for spraying in high or low, more difficult to reach corners Q Switching oN / oFF Switching on: j To start the electrical power tool, press the ON/OFF switch 3 and keep it pressed. Switching off: j To switch off the electrical power tool, release the ON/OFF switch 3. Q Spraying process 1. You can vary the spray by adjusting the regulator button 2 (see Fig. D). The spray is correctly set when no drops are formed and the gun produces a fine, consistent spray pattern. 2. Do not switch the device on or off while it is over the surface to be sprayed. Instead, start 10 GB Bringing into use/Maintenance and cleaning/Service centre/Warranty and stop the spraying process approximately 10cm outside the surface to be sprayed. NoTE: The distance between the nozzle and the workpiece depends on the material being sprayed (approx. 20 to 35cm spraying distance, depending on the spray cone and the desired amount of material to be applied). j Use the device in a horizontal orientation only (as shown in Fig. D). j Carry out a trial in each case to determine the most effective spraying distance. j Start with a longer distance. 3. Spray corners or small decorative details first using short bursts of spray. Then go on to the actual spraying process. 4. The spray process should follow the sequence shown in Fig. E – keep the spray gun moving parallel to the surface – Do not incline the spray gun – Move the spray gun at a constant speed – Apply the sprayed medium as thinly as possible – The layer(s) of sprayed medium need(s) to be allowed to dry for some time before you apply the next coat Fig. F) at right angles to the previous coat. 5. Do not allow the paint cup 7 to empty completely while spraying – drops may form! Q Maintenance and cleaning General advice: 1. WArNING! Pull out the mains plug before you carry out any tasks on the spray gun. Do the same when you take a break from spraying. 2. After each use, spray thinners (in the open air only – danger of explosion!) or water through the device. 3. To protect from rust after cleaning, you can spray sewing machine oil through the device. 4. WArNING! DANGEr To LIFE THroUGH ELECTrIC SHoCK! Never immerse the device in the cleaning medium. 5. Never use inflammable solvents to clean the device. 6. Use a dry cloth to clean the housing. Never use petrol, solvents or cleaning agents that might attack plastic. Cleaning instructions: 1. Unscrew the attachment screw 1 , see Fig. A. 2. Take off the pump housing 10 downwards. 3. Unscrew nozzle 89 . and remove the suction- pressure valve 4. Take the pump piston and spring 5 out of the pump housing 44, 5, 8, 10 . 5. Clean parts 9 with thinners. 6. Fit the components back in reverse order. TIP: After use or cleaning, hang up the electrical power tool from the metal stirrup 14 . Q Service centre J WArNING! Have your electrical power tool repaired only by qualified specialist personnel using original manufacturer parts only. This will ensure that your electrical power tool remains safe to use. J WArNING! If the plug or mains lead needs to be replaced, always have the replacement carried out by the manufacturer or its service centre. This will ensure that your electrical power tool remains safe to use. Q Warranty This appliance is guaranteed for 3 years from the date of purchase. It has been carefully produced and meti-culously checked before delivery. Please keep your receipt as proof of purchase. Contact your service centre by telephone in case of questions pertaining to the warranty. Your goods can be transmitted free of cost only in this manner. This warranty applies only to the initial purchaser and is non-transferable. The warranty c...