Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the air compressor. Check your air compressor’s manual for the appropriate size cord. 18. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. 19. Compressed air only. Never use combustible gas as a power source. 20. Use proper cleaning fluids. Only use noncorrosive, nonflammable cleaning products that are compatible with the materials of this tool, and viscous enough to flow easily through the Nozzle. Only use fluids in the dilution recommended by the manufacturer. 21. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) SKU 93289 For technical questions, please call 1-800-444-3353. Page 3 Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Air Connection Spray Gun For best service you should incorporate a regulator and inline filter, as shown in the diagram above. Hoses, couplers, regulators, and filters are all available at Harbor Freight Tools. 1. You will need to prepare a 1/4”-18 NPS air connector (not included) to connect to the Air Inlet (14) on the Spray Gun. First, wrap the 1/4” air connector with pipe thread seal tape before threading it into the Air Inlet (14). Connect the 3/8” ID air source hose to a quick connect coupler, and then to the Spray Gun. 2. Set the air pressure on the regulator to 40 PSI. Do not exceed 60 PSI. 3. Check the air connection for leaks. Disconnect from the air source. SKU 93289 For technical questions, please call 1-800-444-3353. Page 4 Operation Operation ) FIGURE 1 Fluid Nozzle (1) Air Inlet (14) Trigger (12) Cup (16) Note: Only use noncorrosive, nonflammable cleaning products that are compatible with the materials of this tool, and viscous enough to flow easily through the Nozzle. 1. Remove (un-thread) the Cup (16) from the unit and fill it with cleaning fluid (not included). 2. Replace the Cup (16) making sure it is securely tightened to the unit. 3. Connect the air source hose to the Air Inlet (14) as described in Air Connection on page 4. Set the air compressor to 40 PSI. Note: Runoff may contain hazardous materials that may cause environmental damage if disposed of improperly. Contact your local hazardous waste authority and the cleaning agent supplier for disposal recommendations and regulations (if applicable). 4. Point the Spray Gun at the area needing cleaning and squeeze the Trigger (12). To adjust the flow rate, let go of the Trigger (12), temporarily disconnect the air supply, and unlock the Lock Ring (2). Next, to allow more liquid to flow, loosen the Fluid Nozzle (1), and to allow less liquid to flow, tighten the Fluid Nozzle (1). After adjusted to your satisfaction, tighten the Lock Ring (2) and reconnect the air supply. See FIGURE 2 below. 5. When finished, release the Trigger (12), and disconnect from the air source hose. Point the Spray Gun into a waste bucket, and squeeze the Trigger (12) to make sure no excess air is still in the Spray Gun. FIGURE 2 Lock Nut (2) Fluid Nozzle (1) SKU 93289 For technical questions, please call 1-800-444-3353. Page 5 Maintenance 1. After each use, empty the Cup (16) of any remaining cleaner. Store the fluid in its original container, or dispose of it in accordance with local hazardous waste procedures. Fill the Cup (16) with warm water, set the air compressor to 20 PSI, and connect to the air source hose to the Spray Gun. Point the Spray Gun into a waste bucket and run the entire Cup of warm water through the gun. If the discharged water still smells strongly of the cleaner you used, repeat the process. 2. Wipe down the unit with a lint free cloth. Parts List Part No. Description 1 Fluid Nozzle 2 Lock Ring 3 Air Tube 4 Material Tube 5 Gun Body 6 Bolt 7 0-ring 8 0-ring 9 Air Valve Rod 10 Spring 11 Air Valve Set 12 Trigger 13 Trigger Pin 14 Air Inlet 15 Suction Tube 16 Cup PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS ...