Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
8. Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly. ¦ TRANSPORTATION • Clean and rinse tank and spraying assembly after each use to prevent crystallizing, which would later cause clogging and chemical damage to the unit. • Drain the content from the tank before transporting or storing the sprayer. • Secure the unit carefully to prevent movement when it is transported. •A unit that receives a strong shock during transport and unloading may malfunction. ¦ STORAGE • Clean and rinse tank and spraying assembly after each use to prevent crystallizing, which would later cause clogging and chemical damage to the unit. • Do not store sprayer under pressure, or with spray solution in tank. • When storing the sprayer, choose a space indoors free from moisture and out of the reach of children. ¦ DISPOSAL • When disposing your machine, or chemical, be sure to allow your local regulations. 4. For safe operation 5. Set up Hose clamps are not completely tight. Please tighten hose clamps prior to using. Hose clamps are left loose to extend life of gaskets and fittings. Oil cap gasket before using and lubricate weekly so the gasket will seal properly and prevent chemical leaks. Oil check valve and maintain breather hole clear of debris. Your failure to oil may can cause the tank to collapse and crack due to vacuum created by pump lubricate with "3 and 1" oil. Make sure to insert the locking pin for the pump handle in its (only) CORRECT POSITION. The pin limits the pump stroke for optimum performance without see page. Observe Fig. 1 exactly. (Fig. 2 and 3 spell trouble.) For best results and to maintain a good seal, re-grease piston sleeve periodically with vaseline or similar light lubricants. ¦ HOW TO ASSEMBLE 1. Attach spray wand to spray gun and tighten firmly. 2. Take pump handle RMKIT 7 and insert into the tube on the pump lever RMKIT 5 ("T" shape lever on sprayer), you will notice holes drilled through both sides of both the pump handle and the pump lever. Align these holes, take the "R" pin provided and place through the holes. This affixes the handle in place and is ready for use. For storage reverse process and then place "R" pin through the pump lever RMKIT to keep from losing "R" pin. 3. Instructions for installing shoulder strap plastic buckle: First put the sprayer on a hard flat surface, take the white plastic buckle and while holding the sprayer up slightly, place buckle under the tubular metal frame. Slowly push down forcing the frame into the buckle. Repeat the same procedure for other side. IMPORTANT WARNING NOTE 4. For safe operation 5. Set up Hose clamps are not completely tight. Please tighten hose clamps prior to using. Hose clamps are left loose to extend life of gaskets and fittings. Oil cap gasket before using and lubricate weekly so the gasket will seal properly and prevent chemical leaks. Oil check valve and maintain breather hole clear of debris. Your failure to oil may can cause the tank to collapse and crack due to vacuum created by pump lubricate with "3 and 1" oil. Make sure to insert the locking pin for the pump handle in its (only) CORRECT POSITION. The pin limits the pump stroke for optimum performance without see page. Observe Fig. 1 exactly. (Fig. 2 and 3 spell trouble.) For best results and to maintain a good seal, re-grease piston sleeve periodically with vaseline or similar light lubricants. ¦ HOW TO ASSEMBLE 1. Attach spray wand to spray gun and tighten firmly. 2. Take pump handle RMKIT 7 and insert into the tube on the pump lever RMKIT 5 ("T" shape lever on sprayer), you will notice holes drilled through both sides of both the pump handle and the pump lever. Align these holes, take the "R" pin provided and place through the holes. This affixes the handle in place and is ready for use. For storage reverse process and then place "R" pin through the pump lever RMKIT to keep from losing "R" pin. 3. Instructions for installing shoulder strap plastic buckle: First put the sprayer on a hard flat surface, take the white plastic buckle and while holding the sprayer up slightly, place buckle under the tubular metal frame. Slowly push down forcing the frame into the buckle. Repeat the same procedure for other side. IMPORTANT WARNING NOTE 6. Pre-operation NOTE Hose clamps are not completely tight. Please tighten hose clamps prior to using. Hose clamps are left loose to extend life of gaskets and fittings. WARNING Oil cap gasket before using and lubricate weekly so the gasket will seal properly and prevent chemical leaks. Oil check valve and maintain breather hole clear of debris. Your failure to oil may can cause the tank to collapse and crack due to vacuum created by pump lubricate with "3 and 1" oil. IMPORTANT Before using, oil cap gasket, felt pump washer, and check valve, and maintain breather hole clear of debris. Your failure to oil...