Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
RU 58 - 63 A. B. C. D. E. F. 5. G. H. I. 6.7.8.9.4.12.11.10. A. B. C. D. E. F. 5. G. H. I. 6.7.8.9.4.12.11.10. 1. 2. 3. 13. ' .. Indoor/Outdoor Wireless Thermometer With RCC Clock Instruction Manual Monitor: A. Time B. Date C. Battery Icon D. Indoor Temperature E. Signal Detection Icon F. Outdoor Temperature G. RCC Icon H. Alarm Icon I. Wave OK Icon 1. Max./Min. Button 2. Alarm Button 3. Clear Button 4. Snooze/Light Button 5. (+) Button 6. Set Button 7. (-) Button 8. Wave Button 9. Re-Sync Button 10. DST/Time Zone Button 11. .C/.F Button 12. Reset Button Remote Sensor: 13. Reset Button Before You Begin 1.0 Set up procedure: 1. Insert batteries into the monitor first and then press the RESET button once. 2. Place the monitor as close as possible next to the remote sensor and insert the batteries into the remote sensor and press the RESET button. 3. Position the monitor and remote sensor within effective transmission range, which in usual circumstances is 20 to 45 meters. The range is affected by the building materials and where the monitor and remote sensor are positioned; try various locations for the best results. (See section 3.1). Note: The remote sensor should be placed in a shaded area for accurate readings 1.1 Getting Started Once the remote sensor has been powered up (or the RESET button has been pressed), the transmission signal is immediately sent to the monitor. The monitor will attempt to search for the signal for 5 minutes. Once the signal is received, the dashes (--.-°F) on the monitor will change to the current outdoor temperature. If after 5 minutes the screen does not change to show the outdoor temperature, press the RE-SYNC button on the monitor. The monitor will now attempt to search for the signal for another 6 minutes. 2.0 Troubleshooting 2.0 Troubleshooting Note: to reset unit please see Set up Procedure (see Section 1.0). 3.0 Radio Controlled Clock (RCC) The RCC has the most accurate time within the continent. This unit receives the time Press the RESET button at any time your display shows dashes (--.-°F) and/or ensure that the remote sensor is in direct line to the monitor. If the outdoor temperature cannot be received, check: 1. The distance between the monitor or remote sensor should be at least 0.9 to 1.2 meters away from any interfering sources such as computer monitors or TV sets. 2. Avoid placing the monitor onto or in the immediate proximity of metal window frames. 3. Using other electrical products such as headphones or speakers operating on the same signal frequency (433MHz) may prevent correct signal transmission and reception. 4. Neighbours using electrical devices operating on the 433MHz signal frequency can also cause interference. 5. Signals from other household devices, such as door bells and home security systems, may temporarily interfere with the units and cause reception failure. The transmission and reception of temperature reading will resume once the interference has stopped. The maximum transmission range is 45 meters from the remote sensor to the monitor (in open space). However, this depends on the surrounding environment and interference levels. The temperature signal travels in a straight line from the remote sensor to the monitor. The signal will not curve around an object. If no reception is possible, despite the observation of these factors, all units will have to be reset. signal transmitted by Physikalisch-Technische Bundesanstalt (PTB) of Germany, which is regulated by 4 atomic clocks and in average deviates less than 1 second in 2 million years. PTB transmits the time signal (DCF77, 77.5kHz) continuously from Mainflingen, 25 km southeast of Frankfurt (am Main). It is expected that the signal can cover a distance of 2,000 km from the transmitter. However, some environmental effects may affect the transmitting distance. For more information please see ) 3.1 Environmental Reception Effects 3.1 Environmental Reception Effects With all wireless devices, the receiving ability may be affected by, but not limited to, the following, therefore for best accuracy avoid the following situations: • Long transmitting distance • Nearby mountains and valleys • Among tall buildings • Near railway, high voltage cable, etc. • Near freeway, airport, etc. • Near construction site • Inside concrete buildings • Near electrical appliances • Bad weather • Inside moving vehicles • Nearby metallic structures 3.2 Wave Signal Reception As long as the batteries are supplying power to the monitor, the monitor will receive the time signal and adjust time automatically. No manual adjustment is required after power up. Accurate adjustment of the clock based on the time signal is supported in the continental Europe. The monitor automatically receives the time signal everyday at 1:00am and makes any required adjustment to the time setting, indicated by the flashing RCC icon . If the time signal is successfully received the .................. icon will appear and the RCC icon ...