Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
UTV-1200 Multi Gauge for 2008 Yamaha Rhino Operation menu Left switch functions Pressing the left switch during normal gauge operation will move through the below commonly viewed functions for convenience. 00000.0 Odometer 12:00A Clock (hold left switch to set) Setting clock: Left switch press moves between hours and minutes Right switch press changes current value Hold left switch again to exit clock set mode H 0.0 Hourmeter Right switch functions Pressing the right function switch during normal operation will scroll through the following display functions. A heading will first appear after each press to display the currently selected function. After about 2 seconds, the display will show the data for the selected function. Heading Data Description trip A a 0.0 Trip A (hold right switch to reset) trip b b 0.0 Trip B (hold right switch to reset) srv mi(srv km) s 0000 Count down Service odometer if enabled (hold right switch to reset) srv hr sh 000 Count down service hour meter if enabled (hold right switch to reset) mph(KPH) 00 mph(00 KPH) Alternate speed display (hold right switch to change primary unit) tach r 0000 Tachometer displays in information center INSTALLATION: 1. Disconnect the battery to prevent possible damage to the electrical system or gauge during install. 2. Remove the stock gauge or indicator panel (see service manual for removal instructions). The UTV gauge will mount in this mounting location. 3. Remove the seats, console/engine cover, front engine cover, and center floor/front drive shaft cover (refer to service manual). This allows access to sensor locations on the engine and wire routing locations. 4. Oil sender installation: a. Turn the provided oil sender into the oil pressure sender hose fitting. Sealant tape may be used on this sender as the gauge provides ground through the harness. b. Tighten the sender into the fitting with appropriate wrenches. c. Cut either one of the hoses going to the oil cooler toward the front of the engine to allow the installation of the oil sender T-fixture. It doesn’t matter which hose. Have some rags handy as the hose will leak some oil. d. Place a hose clamp onto each end of the cut oil cooler hose. Two hose clamps are included with the gauge. e. Insert the fitting into the hose and tighten hose clamps onto hose and fitting. f. Remove terminal thumb nuts on oil pressure sender and put ring terminals from oil sender harness onto the terminals. Secure with terminal thumb nuts. The sender terminals don’t have a polarity so just connect one wire to each terminal. g. Route oil sender harness up to the gauge mounting location. Zip tie the harness with provided zip ties so that it will not be pinched or damaged. h. Be sure to check engine oil level and add oil if needed. 5. Route the wires from the UTV gauge through the hole in the gauge opening and place gauge into opening. Secure the gauge with the three provided washers and thumb nuts. 6. Plug the four pin connector from the oil pressure harness into the four pin connector in back of gauge. 7. Locate the 6 pin gauge connector in the Rhino harness. This connector will be located close to the gauge mount location on the under hood side of the dash panel. 8. Plug the 6 pin gauge connector 6 pin connector on the Rhino. 9. Reconnect battery. 10. Turn the key on and verify that the gauge functions as expected. 11. Start engine and check for oil leaks. Shut off engine. 12. If there are no oil leaks, reinstall the floor panels, engine covers and seats as described in the service manual. 13. Installation is now complete. If you experience difficulties check the troubleshooting section in this manual. SETUP a. To enter setup for speed calibration changes: Press and hold left switch while starting engine. b. To enter setup for all other setup options: Press and hold left switch while turning the key on. -Press the left switch to move through the menus or change the settings after a menu option is selected. -Hold the left switch for more than 2 seconds to scroll through options or settings -Press the right switch to select a menu option or to save a setting and go back to the menu. SETUP Release switch to enter setup menu INFO Information menu VER Displays software version U121 Current software version SP CAL Displays current speed cal value 150000 Current speed cal value MAIN Returns to info menu SPEED Speed gauge menu UNIT Select unit for speed Toggle between MPH and KPH (select unit to use for calibration) AUTO Auto calibrate speed to a marked mile or kilometer Pulls up all values .. on speed and speed pulses in odometer Press Right switch to finish cal and save value ADJUST Adjust speed cal while driving ADJUST Each press of left switch toggles direction of adjustment, right switch to save and exit SRV MI (SRV KM) Sets value of service odometer set when service odometer is reset OFF ( OFF) Turns off the count down service odometer (default) 500 ( 800) Sets service to 500 mi or 800 km when resetting service odo...