Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Press again to switch back to listen to the radio. Wake Function Tip: The unit equips with GRADU- WAKE feature, the alarm tone volume will increase gradually to its maximum in about 30 to 45 seconds. Turning Off the Wake Alarm or Radio Press SNOOZE on the top of the unit. The wake alarm or radio will be switched off temporarily. The alarm or radio will be on again when the snooze period is over. (see “SmartSnoozeTM Operation”) To turn off the wake alarm or radio completely, press OFF. The wake alarm or radio will activate again the next day unless you switch off the Wake function (see “Switching off Wake Function”). SmartSnoozeTM Operation This operation allows extra sleep time after the wake function is on. The alarm will be off by pressing SNOOZE, NAP, SLEEP, REV or FWD until the snooze period is over. Snooze function can be used repeatedly up to 30 minutes (default: 9 minutes). Set the “quiet” period as follow: 1. Press and hold SNOOZE. 2. Press REV or FWD to set the quiet period. The time decrements or increments will follow by a faster rate when you press and hold the buttons. Switching Off Wake Function Press WAKE - OFF 1 or 2 repeatedly on the top of the unit until no wake mode icon shows on the display. Sleep Function In sleep mode, you can set the duration (up to 2 hours) before the radio turn off automatically. 1. Press and hold SLEEP on the top of the unit and use REV or FWD to set the duration up to 2 hours (default: 59 min). The time decrements or increments will follow by a faster rate when you press and hold the buttons. Note: The radio will be switched on. NAP Function This function wakes you up after a short period of time (from 10 minutes to 2 hours). 1. Press NAP on the top of the unit and use REV or FWD to set the duration up to 2 hours (each press decreases or increases duration by 10 minutes). 2. The clock time shows after a few seconds if no button is pressed. NAP icon shows on the display to indicate the function is activated. 3. To check remaining nap time, press NAP once to show the time on the display briefly. 4. When the alarm sounds, press OFF to switch it off. • To cancel the function before the nap time ends, press and hold NAP until no NAP icon shows on the display. Wake Function Battery Back-Up Operation This clock radio is equipped with a memory holding system that can be powered with 2 “AA” batteries (included and installed). The power failure protection circuit will not operate unless battery is installed. When normal household power is interrupted, or AC line cord is unplugged, the batteries will power the clock radio to keep track of time and alarm settings programmed into memory. When the battery backup functions, the digital display will not light, however, the function of alarm still occurs during the power interruption if remaining battery power is adequate. Normal operation will resume after AC power is restored so you will not have to reset the time or the alarm. Replace batteries as follow: 1. Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to the tab on battery door and then lift the door out and off the cabinet. 2. Insert 2 AA batteries. 3. Replace the compartment door. Note: we recommend that you replace the batteries every 2-3 years. EN/E FCC Information Important Information Important Information The descriptions and characteristics in this owner’s manual are for the purpose of general reference only and not as a guarantee. In order to provide you with the highest quality product, we may make changes or modifications without prior notice. The English version serves as the final reference on all product and operational details should any discrepancies arise in other languages. Clock Projector A clock projector is located on the left side of the unit. Clock time can be projected onto ceilings or walls for easy reference. The distance between the projector and the projected surface should be within 2.6 to 9 feet (0.8m to 2.8m) . The projector can be rotated 90o forward or backward. Slide the PROJECTOR switch to turn on or off the projector. To rotate the projected image, press ANGLE repeatedly. Each press will rotate the image by 90o. The clock time can also be displayed temporarily from the projector even if it is switched off. Press SNOOZE/PROJECTION once to display the clock time for about 10 seconds. Thermometer Thermometer EXPORTER Thomson Inc. P.O. Box 1976 Indianapolis, IN 46206 - 1976 ©2006 Thomson Inc. Trademark(s) ® Registered Marque(s) ® Deposee(s) Marca(s) ® Registrada(s) Printed in China / Impreso en China IMPORTADOR Comercializadora Thomson de Mexico, S.A. de C.V. Alvaro Obregon No. 151. Piso 13. Col. Roma. Delegacion Cuauhtemoc C.P. 06700. Mexico, D.F. Telefono: 52-55-11-020360 RFC: CTM-980723-KS5 • Make sure that you keep your set away from water and high temperatures. • Do not use your System immediately after transporting it from a cold place to a warm place, as condensation may cause...