Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
•The clock beeps and display illumination flashes for about three seconds when a receive operation trigged by the WAVE button (4) is successful. Important! •Do not perform any button or switch operation while a signal receive operation is in progress. •The time calibration signal includes both Standard Time and Daylight Saving Time (summer time) data. •The DST indicator appears on the display when Daylight Saving Time (summer time) data is received. Setting the Time and Date Manually •When using the clock in an area that is outside of the range of the transmitter in Rugby or in an area where signal reception is impossible for some reason, you need to manually adjust the time as required. 1. Press the SET button (3) to cycle through the setting screens as shown below. Normal Timekeeping Screen Year Setting Screen 12-hour/24-hour Timekeeping Screen Month and Day Setting Screen Time Setting Screen 2. While the screen you want is on the display, use the Alarm Time Set buttons (2) to change the digits that are flashing. SET UP(+) WAVERE-SYNC ° C / ° F DOWN(–) RESET TEMP. MAX/MIN CLEAR Press — to decrease the flashing digits. Press + to increase the flashing digits. •Holding down + or – changes the flashing digits at high speed. •You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with the date setting. •Pressing + or – while the Time Setting Screen is on the display causes the seconds count to be reset to 00. •Each press of + or – while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour and 24-hour timekeeping. 3. After making the settings you want, use the SET button (3) to display the Normal Timekeeping Screen. •The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for about three minutes without performing any operation. USING THE ALARM The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm Mode selector (5) to select the snooze alarm feature. Setting the Alarm Time Use the Alarm Time Set buttons (2) to set the alarm time. Pressing the Alarm Time Set buttons (2) causes the alarm time to appear in place of the date on the display. SET UP(+) WARE-SYNC ° C / ° F DOWN(–) RESET TEMP. MAX/MIN CLEAR Press to change the alarm time setting (—). Press to change the alarm time setting (+). •Holding down + or – changes the digits at high speed. Turning the Alarm On and Off Use the Alarm Mode selector (5) on the side of the clock to turn the alarm on and off, and to select the snooze feature. Alarm Mode selector SNZ ( ) ALM ON ( ) ALM OFF Description The alarm sounds at the preset time for one minute, and seven more times every five minutes thereafter. Even if you stop the alarm sound by pressing the SNOOZE/LIGHT button (1), the alarm operation is performed again five minutes later. •The indicator flashes on the display to indicate that the snooze feature is activated. The alarm sounds at the preset time for one minute. The alarm does not sound. •The alarm time appears in place of the date on the display whenever the Alarm Mode selector (5) is set to ON or SNZ. •The light also turns on for the first four seconds that the alarm sounds. •The alarm sound changes over four levels as it sounds. Stopping the Alarm •When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on, the alarm will sound again in about five minutes. •To turn off the snooze feature, slide the Alarm Mode selector (5) to OFF. Operation Guide DQR-100U 4 USING THE LIGHT Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark. Important! •Overuse of the light can shorten battery life. BATTERY REPLACEMENT Low Battery Warning A indicator appears on the display to let you know when battery power is low. Replace the batteries as soon as possible. Note that the indicator appears on both the main unit and sub-unit when sub-unit battery power goes low. To replace main unit batteries Replace batteries whenever the display of the clock becomes dim and difficult to read. 1. Open the battery compartment cover as shown in the illustration. 2. Remove all of the old batteries. 3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct directions. If you load batteries incorrectly, they can burst and damage the clock. 4. Replace the battery compartment cover. 5. Press the RESET button (6). Be sure to press the RESET button (6) after replacing batteries. To replace sub-unit batteries 1. Rotate the battery compartment cover from LOCK to OPEN. 2. Remove both old batteries. 3. Load new batteries. Make sure that their positive (+) and negative (–) ends face in the correct directions. If you load batteries incorrectly, they can burst and damage the clock. 4. Replace the battery compartment cover. 5. Press the RESET button (B). Be sure t...