Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
This may be necessary if it is not possible to sit centrally between the speakers. In normal use leave in the central 'click' position. © ZONE 1 - Push the button in to activate the ZONE 1 preamp out sockets. With the button in the out position the ZONE 1 preamp out sockets are muted. © ZONE 2 - Push the button in to activate the ZONE 2 preamp out sockets. With the button in the out position the ZONE 2 preamp out sockets are muted. © HEADPHONES SOCKET - Accepts headphones rated between 8 ohms and 2k ohms fitted with a 6.3mm stereo jack plug. If your headphones are fitted with a different plug contact your dealer for a suitable adaptor. ■ If you wish to listen on headphones only use the remote handset MUTE button to mute the main preamp out sockets. ENGLISH NB:lf you now wish to adjust the volume you need to do this manually as use of the volume buttons on the remote will un-mute the preamp outputs and allow signal to go to your power amps again. Alternatively you may be able to switch off the speakers connected to your power amplifier. ■ The ZONE 1 and ZONE 2 outputs will remain live and can be switched off with use of the front panel ZONE buttons. ■ The headphone socket is always switched on, irrespective of the positions of switches © and © or the remote control MUTE function. © POWER - Switches the unit on and off. © POWER LED - The LED above the POWER switch will initially glow amber. After a few seconds, it will glow green. When the LED glows amber, the preamp out sockets are disconnected . The power led will also glow amber if the unit has been muted by use of the remote. © REMOTE RECEIVER - The remote receiver is behind the badge in the top left hand corner of the unit. Ensure the remote receiver is not obscured or commands from the remote control handset will not be received. TAPE RECORDING ■ Both sets of tape sockets (TAPE 1 and TAPE 2) are identical in sensitivity and suitable for use with almost any type of recorder (cassette, hi-fi VCR, reel to reel, MD, etc.) RECORDING (TAPE 1) Use the SEND selector © to route the required signal to a cassette deck connected to the TAPE 1 RECORD OUT sockets ©. Set your tape recorder into its recording mode and the selected input will be recorded. Selecting the same input with the LISTEN selector will not affect the signal sent out to the recorder and will now enable you to listen to the signal being recorded. If your tape recorder is a 3 head design, this will allow A-B monitoring of the actual recording while it is taking place. Switching the LISTEN switch between the original source and TAPE 1 during recording will then enable you to make a true ‘before’ and ‘after’ (A-B) comparison. You may listen to another input whilst recording on TAPE 1 by use of the LISTEN selector. RECORDING (TAPE 2) Use the LISTEN selector © to route the required signal to a cassette deck connected to the TAPE 2 RECORD OUT sockets © Set your tape recorder into its recording mode and the selected input will be recorded. To monitor the recording push the PROCESSOR/ TAPE 2 button in. If your tape recorder is a 3 head design, this will allow A-B monitoring of the actual recording while it is taking place. You may record another input on to TAPE 1 whilst recording on TAPE 2 by use of the SEND selector. ■ TAPE TO TAPE DUBBING: The Alpha 9C allows two way tape dubbing (copying) from TAPE 1 to TAPE 2 or vice versa. For example, to copy from a recorder connected to the TAPE 2 sockets to a recorder connected to TAPE 1, first switch the SEND selector on the Alpha 9C to TAPE 2. This routes the TAPE 2 signal to TAPE 1's output. Then set the first tape recorder into its 'record' mode and the second to 'playback' mode to enable the transfer to take place. If you wish to monitor the transfer while it is taking place switch LISTEN to TAPE 1. To record from TAPE 1 to TAPE 2 set LISTEN to TAPE 1. It does not matter what position the SEND selector is in. To monitor push the PROCESSOR/ TAPE 2 button in. REMOTE CONTROL FUNCTIONS ■ Your Alpha 9C preamplifier is supplied with the Arcam CR35 infra-red remote control handset, which has buttons to allow the simple operation of other products. It is supplied with 2 AA batteries - ensure these are inserted correctly. ■ The remote handset enables you to operate the LISTEN/ ZONE 1 SELECTOR, VOLUME and MUTE functions on the Alpha 9C. It also allows you to control some basic functions of an Arcam or Philips based CD player (except the Alpha One CD player, which uses a different remote control language) and a remote controlled tuner (such as the Alpha 8 tuner). ■ REMOTE MODE - The Alpha 9C is factory-set to enable the Arcam CR35 or Arcam CR200 System Remote automatically to synchronise the operation of any Arcam CD player or transport, and remote control tuner with the LISTEN/ZONE 1 SELECTOR on the Alpha 9C, all at the touch of a single button. For example, using the CR35 remote, press PLAY, and the CD player will start the disc and the...
Otros modelos de este manual:El receptor y el amplificador - PreAmplifier Alpha 9C (5.9 mb)