Votos - 5, Puntuación media: 4.8
(
)
)
|
Resumen del manual
22. SGL/CTN -This function allows you to choose between single track play or continuous track play (all tracks in order). This function also operates in PROGRAM and FLIP FLOP modes. 23. RELOOP BUTTON -If a SEAMLESS LOOP has been made (see setting a SEAMLESS LOOP on page 17), but the CD Player is not actively in SEAMLESS LOOP mode (a loop is not playing), pressing the RELOOP BUTTON will instantly reactivate the SEAMLESS LOOP mode. To exit loop, press the OUT BUTTON (24). LOOP and RELOOP will appear in the LCD DISPLAY (34) when the RELOOP function is available. 24.OUT BUTTON -This button is used to set the ending point of a loop. A loop is started by pressing the IN BUTTON (25), pressing the OUT BUTTON set the loop ending point. The loop will continue to play until the OUT BUTTON is pressed once again. 25. LOOP IN BUTTON - “CUE ON THE FLY” - This function allows you to set a CUE POINT (see CUE POINT page 18) without music interruption (“on the fly”). This button also sets the starting point of a seamless loop (see SEAMLESS LOOP). 26.(-) PITCH BEND BUTTON -The (-) pitch bend function creates a momentary “Slow Down” in the CD’s BPM’s (Beats per minute) while it is playing. This will allow you to match the beats between two playing CD’s or other playing music source. Remember, this is a momentary function. When you remove your finger from the pitch button, the BPM’s will automatically return to PITCH SLIDERS (18) pitch value Holding down this button will give a maximum of -100% pitch. Use this function to slow to another playing music source. Be sure to notice that this function is a momentary pitch adjustment, for a more precise adjustment use the PITCH SLIDER (18) to match the BPM’s with another playing music source. (+) PITCH BEND BUTTON -The (+) pitch bend function creates a momentary “BUMP” in the CD’s BPM’s (Beats per minute) while it is playing. This will allow you to match the beats between two playing CD’s or any other music source. Remember, this is a momentary function. When you remove your finger from this button, the BPM’s will automatically return to PITCH SLIDERS (18) selected pitch. Holding down this button will give a maximum of +100% pitch. 27. PITCH PERCENTAGE SELECTOR-Choose from pitch percentages of 4%, 8%, 16%, and 100%. See page 28 for more details. 28. BPM BUTTON -The BPM button is used to toggle between two readouts in the LCD (34). When the BPM function is activated, the LCD (34) will display a BPM meter. The BPM meter will automatically and accurately detail a tracks beats per a minute (BPM). When this function is not active the LCD will display the amount of ©American Audio® --DCD-PRO1000™ Instruction Manual Page 11 GENERAL FUNCTIONS AND CONTROLS (Cont.) GENERAL FUNCTIONS AND CONTROLS (Cont.) 29. BANK BUTTONS 1-3 -These button are used to store either three (3) cue points or three (3) samples. Each Bank Button can store either a sample or a cue point. 6 sec. samples each bank. 30. SAMPLER BUTTON -This is used to activate the sampler function. When this function is activated a created sample will play in a continuos loop, until the sampler is deactivated. 31. MEMORY BUTTON - This button allows you to program up to 3 cue points or three samples in to the three FLASH BUTTONS (29). The samples or cue point can then be recalled at any time even when the disk has been removed and reloaded at a later time. 32. PLAY/PAUSE BUTTON -Each press of the PLAY/PAUSE BUTTON causes the operation to change from play to pause or from pause to play. While in play mode the green play L.E.D. will glow, and while in pause mode the green play L.E.D. will flash. 33. CUE -Pressing the CUE button during playback immediately pauses playback and returns the track to the last set cue point (see setting a CUE POINT, page 18). The red CUE L.E.D. will glow when the unit is in cue mode The L.E.D. will also flash every time a new CUE POINT is set. The CUE button can be held down to momentarily play the CD. When you release the CUE button it instantly returns to the CUE POINT. You can also tap the CUE button to create a BOP EFFECT (for definition of BOP EFFECT, see page 24). 34. LCD DISPLAY - This high quality LCD display indicates all the functions, as they are occurring. This display is viewable at several comfortable angles (see page 8). The display ICONS will be explained on page 15. B. REMOTE CONTROL -REAR 35. CHANNEL 1 REMOTE JACK -Connect the supplied 8 pin din cable from this jack to the player's channel 1 remote connector. This will allow you to control the functions of player 1. 36. CHANNEL 1 CONTROLLER JACK -Connect the supplied mini-plug from the CUE jack on the rear of your CD unit to the CONTROL out jack of a compatible American Audio® or American DJ® mixer. This will enable the CD "Q-Start" function. This feature is only available on American Audio® or American DJ® “Q” series mixers. 37. CHANNEL 2 REMOTE JACK -Connect the supplied 8 pin din cable from this jack to the player's channel ...