Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Sound is flat at the center position. Turn to the right to increase (to approximately +12 dB at 10 kHz) Turn to the left to decrease (to approximately –24 dB at 10 kHz) LOW: Adjusts the low tone microphone sound. Sound is flat at the center position. Turn to the right to increase (to approximately +12 dB at 100 Hz) Turn to the left to decrease (to approximately –24 dB at 100 Hz) •Input of MIC 1 and MIC 2 is mixed and output through the MASTER OUT 1 left (L) and right (R) terminals. Note The channel fader and cross fader used with this unit are designed for extended use however, depending on the way they are being used (e.g. quick, repetitive movements such as Hip Hop transfer play,etc.) replacement may be necessary. •Contact your nearest dealer to have your channel fader and or cross fader replaced. •To the dealer: The “Fader Replacement Instructions” are included with the replacement product. Replacement part number Channel fader (Part No. REP3743A-S) Cross fader (Part No. REP3742A-S) Mixing (Basic operations) Changing the channel fader, cross fader operation method Use the channel fader switch to change the operation method for each channel. (e.g. using CH1) Switch [CH1 FADER] and [CROSS FADER] NORMAL: Operation is as indicated on the panel REVERSE: Operation is reverse as indicated on the panel Changing the cross fader curve Select from 1 of 3 types of cross fader startup curves. Switch [CURVE] Output level meter display •The mixed left (L) and right (R) volume level of the selected channel (CH1-CH4) is displayed in the LEFT and RIGHT columns of the output level meter. Display range: –20 to +8 dB •Even if the MASTER LEVEL or MASTER BALANCE is changed the OUTPUT LEVEL meter display does not change. OUTPUT LEVEL meter Recording and playing on external equipment You can record and play on externally connected equipment. Using the REC OUT terminal The same source as MASTER OUT 1 is output. Using the DIGITAL OUT terminal The same digital signal source as MASTER OUT 1 is output. Even if the MASTER LEVEL or the MASTER BALANCE is changed the REC OUT or DIGITAL OUT output does not change and recording or play remains unaffected. RQT7230 11 Additional mixing operations Adjusting the monitor You can check the sound on the headphones etc. during play and cue the channel you want to mix, and adjust the volume and check the mixing sound. Monitoring CH1 1 Press [CUE CH1] to turn on the monitor sound •The display lamp lights once the CUE button is pressed. •Monitor sound from the selected channel is output to PHONES (Headphones) and MONITOR OUT terminal. •Mixed sound can be output by pressing multiple CUE buttons. When using an effector ( left side of this page) Press [CUE EFFECT] to turn on the monitor sound •Monitor EFFECT RETURN is output. 2 Select the input, adjust the input level, sound, and adjust the volume with the channel fader and cross fader ( page 9, Mixing, instructions 3 - 7) 3 Turn [MIXING] and adjust mixing •Turn completely to the right for audio from the master output. •Turn completely to the left for audio from the channel selected with the CUE button. •When the control knob is in the center position the audio level of the master output and the channel selected with the CUE button is half and half. •The monitor volume level is displayed in the MONITOR column of the output level meter. 4 Switch [MODE] and select the monitor sound You can select the monitor sound to be stereo or split between the channel selected with CUE button (L) and master (R). Select MONO SPLIT and the monitor output will become monaural, left (L) will output audio from the channel selected with the CUE button, and the right (R) will output audio from the master output channel. 5 Turn [LEVEL] to adjust the monitor volume •Even if the MASTER LEVEL and MASTER BALANCE is changed the monitor sound does not change. Adjusting the effect You can adjust the volume level and select the output point when using an externally connected effector. 1 Switch [EFFECT] to ON Outputs to the external effector. 2 Switch [PRE/POST] and select the output point PRE: Outputs before the channel fader POST: Outputs after the channel fader 3 Turn [SEND] to adjust the output level Adjusts the output volume level sent to the external effector. 4 Turn [RETURN] to adjust the input level Adjusts the input volume level from the external effector. •An effect is applied to the input source sound and output to the MASTER OUT 1 terminal. On the channel you have selected to use effect output OUTPUT LEVEL meter Using output separation When using output separation (dual output separation) ( page 12), audio is output through the MASTER OUT 2 (REAR) terminal. RQT7230 12 Using play mode functions 1 Switch to either [L/R SPLIT (CH1 CH2)] or [L/R SPLIT (CH3 CH4)] and select the channel to adjust individually The input of the selected channel is allocated to the channel to be adjusted on the panel. CH1 or CH2 input: Left (L) is input to CH1 on the panel, right (R) is input to CH...
Otros modelos de este manual:El receptor y el amplificador - SH-MZ1200 (1.84 mb)