Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Important safety instructions 1. Do not expose the receiver to direct sunlight, high humidity, dirt, heavy vibration or extreme temperatures. 2. Place the unit on a solid and plane surface. 3. Make sure that there is sufficient ventilation around the receiver. Do not place the unit on a soft surface such as a carpet. Make sure that there is a clearance of 20 cm behind the unit. 4. Do not open the cabinet. Only qualified technicians are allowed clean the internal parts. 5. Make sure that liquid and foreign matter cannot penetrate the unit. 6. If service or repair is required, this must be carried out by qualified technicians. 7. Unplug the unit in the following cases: A.The mains plug or the mains cable is defective. B.Foreign matter or liquid has penetrated the receiver. C. The unit cannot be operated properly. D.The unit has fallen down or the cabinet has been damaged. 8. Store this instruction manual carefully for future reference. 9. Use a duster or a slightly damp, soft and non- fluffy rag to clean the receiver. 10. Do not use corrosive or strong cleaning agents. Make sure that no moisture penetrates the receiver during cleaning. Unplug the unit before cleaning. 11. The fuse of the unit is accessible to the user but shall only be replaced by qualified technicians if required. 12. Check that the mains voltage indicated on the back of the receiver corresponds to the mains voltage that the unit is connected to. 13. Read the instructions under "Troubleshooting" before handing in the receiver for repair. 14. Unplug the unit if the receiver is not to be used for a long time. Disclaimer Despite extensive efforts we cannot guarantee that the technical data indicated are correct, complete and updated. We reserve the right to make technical changes without notice. Please read these safety instructions carefully before you start using the receiver! 04 Remote contro l Installation of batteries Remove the cover as illustrated. Insert two batteries of the type AAA/R03/UM4. Make sure that the terminals correspond to the symbols shown (see bottom). Replace the cover. Do not mix new and old batteries, and do not use different types of batteries. If the remote control is not used for prolonged periods, remove the batteries from the remote control to prevent corrosion. Using the remote control Aim the remote control at the sensor on the receiver's front panel. When the remote control signal is received, the receiver will respond accordingly. The remote control works within a range of about 6m. Do not expose the unit to strong sources of light. This may disable the use of the remote control. Do not use other remote controls near the unit. This may cause a malfunction. Do not place any objects on the remote control as the batteries may be discharged if a key is depressed continuously. Do not place large objects between the remote control and the receiver. Do not place the receiver behind tinted glass. This will reduce the range of the remote control. 05 STANDBY SPEAKER Infrared- Sensor VOLUME MODE DSP INPUT TUNING BAND C-102 HOME THEATRE RECEIVER STANDBY Remote contro l Remote control functions STANDBY SPEAKER 1. Standby 2. Digital Optical Input 3. Digital Coaxial Input 4. AUX1 5. TV 6. RDS 7. Band (FM/AM) 8. DSP mode 9. SPK mode (Speaker mode) 10. Balance 11. Center delay + 12. Center delay 13. Tuning up 14. Tuning mode 15. Preset 16. Tuning down 17. Mute 18. Volume decrease 19. AUX 2 20. Tuner 21. Memory 22. Mono/Stereo (FM) 23. Night (Dynamic Compression) 24. Test 25. Mode [Stereo/PL II Musik/ PL II Movie, DTS/Dolby Digital] 26. Surround delay + 27. Surround delay 28. Speaker A/B selector 29. Preset + 30. Bass Boost 31. Volume increase Some of the AV receiver's functions can only be performed by means of the remote control. Some functions are connected with the signal input source selected. Some keys on the remote control thus may not be available if the corresponding signal input source has not been selected. 06 Front panel and connections Front panel Connections 1. Standby On/Off 2. Standby LED 3. Headphone 4. Mode (Dolby Digital, DTS, PL II Movie, PL II Music, Stereo) 5. DSP Program 6. Speaker A selector 1. Front speaker A output 2. Front speaker B output 3. FM antenna input 4. Digital input (Optical + video) 5. AM antenna input 6. Digital input (Coaxial + video) 7. AUX 1 input (Analog stereo + video) 8. AUX 2 input (Analog stereo + video) 07 VOLUME STANDBY HEADPHONE MODE DSP INPUT TUNING BAND SPEAKER A SPEAKER B 1 2 3 4 5 6 7 8 9 10 11 12 7. Input selector 8. Speaker B selector 9. Tuning 10. Band (FM/AM) 11. Display 12. Multijog SERIAL NO.: AV RECEIVER MODEL: Cilo C-102 ITEM NO.: 11098.01 POWER SOURCE: 220-240V~50/60Hz POWER CONSUMPTION: 200W MAX FRONT SPEAKER OUTPUT FM - ANTENNA - AM OPT. VIDEO COAX VIDEO AUX 1 AUX 2 SUB SCART INPUT/OUTPUT SPEAKER OUTPUT CEN. SW SR SL R L SPEAKER A R L SPEAKER B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 9. Subwoofer preout 10. Scart input/output 11. Center speaker output 12. Subwoofer ...