Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
If any of these items are missing, please contact Harman Kardon customer service at • System and Zone 2 remote controls • EzSet/EQ II microphone • Extension rod for EzSet/EQ II microphone • docking station for iPod • AM loop antenna • FM wire antenna • Six AAA batteries • AC power cord * Compatible with most docking iPod models, 4G and later. Video and still-image viewing requires an iPod that supports video browsing. 7 USB ENGLISH FRONT-PANEL CONTROLS Power indicator Standby/On Switch Info Settings Main Power Switch AVR Settings Resolution Video Modes Source List OK USB Port Digital Audio Inputs (Optical and Coaxial Front) Video Inputs (S- and Composite Front) EzSet/EQ II Microphone Input Back/Exit Audio Effects Surround Modes Menu Analog Audio Front Inputs Headphone Jack KLM N Navigation Remote IR Sensor Message Display Volume Power Indicator: This LED has three possible modes: •• Main Power Off: When the AVR is unplugged or the Main Power Switch is off, this LED is off. •• Standby: Amber indicates that the AVR is ready to be turned on. •• On: When the AVR is turned on, this LED turns white. NOTE: If the PROTECT message ever appears, turn off the AVR and unplug it. Check all speaker wires for a possible short. If none is found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again. Standby/On Switch: This electrical switch turns the receiver on, or places it in Standby mode for quick turn-on. Front-Panel Door (not shown): Most of the controls and connectors described below are hidden behind this door. To open it, gently grab the right or left edge of the door and pull it forward and down. Main Power Switch: This mechanical switch turns the power supply on or off. It is usually left on, and cannot be turned on or off using the remote control. AVR Settings Button: Press this button to access the AVR’s main menu. Info Settings Button: Press this button to directly access the AVR’s Source Info submenu, which contains the settings for the current source. Resolution: Press this button to access the AVR’s video output resolution setting: 480i, 480p, 576i, 720p, 1080i or 1080p. IMPORTANT NOTE: If the AVR’s video output resolution is set higher than the capabilities of the actual connection, you will not see a picture. If the best available video connection from the AVR to the TV is either composite or S-video, press this button and change the resolution to 576i. Audio Effects: Press this button to directly access the Audio Effects submenu, which allows adjustment of the tone and other audio controls. See the Initial Setup section for more information. Video Modes: Press this button for direct access to the Video Modes submenu, which contains settings that may be used to improve the picture, if necessary, after you have adjusted the picture settings using the video display or TV. Surround Modes: Press this button to select a surround sound (e.g., multichannel) mode. The Surround Modes menu will appear on screen, and the menu line will appear in the front-panel display. See the Advanced Functions section for more information on surround modes. Source List: Press this button to select a source device, which is a component where a playback signal originates, e.g., DVD. Menu Button: Press to display the menus for the tuner, the USB device, The Bridge II, the Network or Internet Radio, when any of those sources is in use. Back/Exit: Press this button to return to the previous menu, or to exit the menu system. FRONT-PANEL CONTROLS FRONT-PANEL CONTROLS KLM N Navigation: These buttons are used to navigate the AVR’s menus, including the menus for the tuner, the USB device, The Bridge II, the Network and Internet Radio. OK: Press this button to select the currently highlighted item. Headphone Jack: Plug a 1/4" stereo headphone plug into this jack for private listening. USB Port: Connect a USB flash drive, to play audio files in the MP3 or WMA format or still images in the JPEG format. DO NOT connect a PC, keyboards, pointing devices or other peripheral products to the AVR 760/AVR 660. Do not connect an iPod here; use The Bridge II instead. Do not connect a USB hub or multi-card device. Digital Audio, Video and Analog Audio Front Inputs: Connect a source component that will only be used temporarily, such as a digital camera or game console, to these jacks. Use only one type of audio and one type of video connection. Note: The AVR’s menus refer to these jacks as the Optical Front, Coaxial Front, Composite Front, S-Video Front and Analog Front inputs. EzSet/EQ II Microphone Input: This jack is used to connect the supplied microphone for the EzSet/EQ II procedure described in the Initial Setup section. Volume Knob: Turn this knob to raise or lower the volume. Message Display: Various messages appear in this two-line display in response to commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line...
Otros modelos de este manual:El receptor y el amplificador - 760 (926.66 kb)