Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Carefully splice and insulate all wire connections. CAUTION: CAUTION:CAUTION:CAUTION:CAUTION:CAUTION: Use either the low-level or the high-level inputs on the amplifier. DO NOT DO NOTDO NOTDO NOTDO NOTDO NOT use both input levels at the same time. -5 USE THIS INPUT WIRING WITH STEREO AND MIXED-MONO INPUT WIRING DIAGRAM OUTPUT WIRING ON PAGE 7 LOW-LEVEL HIGH-LEVEL CAR STEREO (SPEAKER) OUTPUTS RCA OUTPUTS LEFT RIGHT RIGHT + LEFT LEFT + RIGHT IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT BOTH. RCA TYPE4-PIN SHIELDED CABLECONNECTOR (NOT INCLUDED) WHITE WHITE w/BLACK STRIPEGRAYGRAY w/BLACK STRIPE REMOTE CONTROL 6OFF 12dB 18dB -6 USE THIS OUTPUT WIRING WITH INPUT WIRING ON PAGE 6 STEREO AND MIXED-MONO OUTPUT WIRING DIAGRAM CONNECT THIS WIRE LAST + LEFT RIGHT SPEAKER SPEAKER - + STEREO MODE : 2-8 OHMS MIXED-MONO MODE : 4-8 OHMS STEREO MODE : 2-8 OHMS MIXED-MONO MODE : 4-8 OHMS CAR STEREO + - AUTO-ANTENNA LEAD MIXED-MONO SPEAKER OR SUB-WOOFER WITH CROSSOVER 4-8 OHMS EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE FROM AREA FOR GOOD CONNECTION GROUNDED METAL SECTION OF VEHICLE 12 VOLT VEHICLE BATTERY CHASSIS GROUNDUSE #10 GAUGE WIRE (SEE TEXT) -7 MONO (BRIDGED) INPUT WIRING DIAGRAM MONO (BRIDGED) INPUT WIRING DIAGRAM USE THIS INPUT WIRING WITH OUTPUT WIRING ON PAGE 9 HIGH-LEVEL LOW-LEVEL (SPEAKER) OUTPUTS CAR STEREO - RCA OUTPUTS TO 2nd AMPLIFIER 4523"Y" RCA TYPE SHIELDED CABLE (NOT SUPPLIED) 1IMPORTANT USE EITHER HIGH OR LOW-LEVEL INPUTS, NOT BOTH. + - + TO 2nd AMPLIFIER 4-PIN CONNECTORWHITE w/BLACK STRIPEWHITEGRAYGRAY w/BLACK STRIPE REMOTE CONTROL 6OFF 12dB 18dB -8 USE THIS OUTPUT WIRING WITH INPUT WIRING ON PAGE 8 MONO (BRIDGED) OUTPUT WIRING DIAGRAM CONNECT THIS WIRE LAST + MONO SPEAKER OR SUB-WOOFER 4 - 8 OHMS - CAR STEREO AUTO-ANTENNA LEAD USE #10 GAUGE WIRE (SEE TEXT) 12 VOLT VEHICLE BATTERY CHASSIS GROUND EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE FROM AREA FOR GOOD CONNECTION GROUNDED METAL SECTION OF VEHICLE -9 OPERATION After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. 1 Power Indicator The Power LED functions as a power and warning indicator. The indicator is white when the power to the amplifier is off. When the indicator is green, the amplifier is operating normally. The LED illuminates red to indicate that the self-protection circuits have been activated and have shut off operation of the amplifier. The protection circuits may be triggered by the temperature of the unit rising above a safe level or by an overload condition. If activated by a rise in temperature, the unit will resume operation after cooling off to a normal operating range. If activated by an overload condition, the source of the overload must be found and corrected to resume operation of the amplifier. Most overload conditions are caused by mis-wiring or operation into incorrect speaker loads. Re-check all wiring and connections if this situation occurs and correct as necessary. 2 Level (Gain) Control The amplifier is capable of operating from sources supplying a wide range of input levels. The Level control should initially be set to the mid-rotation position. If it is found that there is not enough output even when the volume control on the car stereo is at its maximum setting, adjust the Level control to increase the output from the system. If, however, there is still output from the amplifier when the car stereo volume control is at its minimum setting, or the output level increases too fast with a small rotation of the volume control, adjust the Level control to decrease the output from the system. Once the correct setting is found, this control should not require any further adjustment. -10 3 Filter Selector This switch allows selection of the frequency filters that permit the amplifier to be used to reproduce the entire audio range, just the bass, or all frequencies above the bass range. In the "OFF" position of the switch, the response is flat and unaffected so the entire audio frequency range is reproduced by the amplifier. Use this setting if the amplifier is being used to power a full range speaker system. In the "LOW PASS" setting, only the bass frequencies below the frequency set by the Crossover Frequency Control will be amplified and fed to the speakers. Use this setting if the amplifier is being used to power a sub-woofer speaker system. In the "HI-PASS" setting, only the frequencies above the frequency set by the Crossover Frequency Control will be amplified and fed to the speakers. Use this setting if the amplifier is being used to power the full-range speakers in a system that also has separate sub-woofer(s). 4 Crossover Frequency Control This Control selects the crossover frequency when the Filter Selector is in the "LOW-PASS" or "HI-PASS" settings. Adjust it to the appropriate position for the characteristics and crossover frequency requirements of the speaker system with...