Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
0MIN MAX 55 250 GAIN LOW 10 50 SUB SONIC R L BOOST 15 BASS Speaker outputs This amplifier is a multi channel amplifier design. Meaning it has more than one channel of speaker outputs. It is equipped with a large block style terminal for speaker connection. Make this connection carefully and neatly. Strip your wire back and twist the exposed leads and insert them into the block terminal while being careful that there is no loose or frayed strands of wire and tighten the Allen head screw down on the terminal till the wire is tightly secured in place. If the wires ever come in contact with each other the amplifier will go into protection. Know your total ohm load before you make any connections. RIGHT BRIDGED LEFT REAR FRONT FUSES 25 X 2 Installation Instructions 1. Before you start, disconnect the negative cable from the car battery. Tape up the end so it is isolated form the battery. 2. Run an appropriate gauge wire from the battery to the amplifier. Plan this part of the installation carefully. This cable will carry very high current. If it should short to the body and it is not properly fused it could catch fire. 3. Connect the power wire to the battery using a fuse capable of the total current load of all amplifiers connected. Don’t install the fuse yet. Wait until the end. Locate the fuse as close as possible to the battery. If the fuse is further that 18 inches (wire length) from the battery you should reevaluate the wire and fuse placement. 4. Find the closest clear metal area to the amp for a ground. Sand, grind or scrape all paint and undercoating from the body and screw the ground securely in place. It is advisable to test the ground with an ohmmeter between the ground cable and the negative battery cable to insure a good low resistance connection. Some alloys used in modern cars do not offer the best ground. If you believe this is the case consult with the vehicle manufacturer. 5. Run the speaker wire to the speakers. It is advised that you leave some extra wire at this point. You can “ clean it up” later. 6. If you haven’t already done so, mount the amp now. 7. Connect the power and ground to the amplifier. Only after this step should you install the fuse at the battery. 8. Connect the remote wire from the head unit to the amplifier. Now is a good time to turn on the amp for the first time. Make sure it turns on properly and does not go into protection. 9. Connect the speaker wires to the amp and speakers (make sure the amp is off first). Make sure the polarity (+ and-) is correct. 10. Connect the RCA’s to the amp. 11. Double check the amplifier controls at this time. Make sure everything is set correctly for your system. 12. Now you’re ready to play it for the first time. It is best to leave the gain all the way down at first. Start with the head unit volume low and work your way up. 13. Now you can tune the amp. Take your time and make only one adjustment at a time. It may take some time to get the system fully adjusted. During this time the amp is drawing current from the battery. You should check the battery voltage from time to time and re-charge it if it gets low. That’s it. You’re done. Now have fun. SPECIFICATIONS XDi 803 XDi 804 XDi 805 XDi 600.1 XDi 1000.1 POWER OUTPUT @ 4 . 80 X 2 240 X 1 80 X 4 80 X 4 240 X 1 250 X 1 400 X 1 POWER OUTPUT @ 2 . 120 X 2 400 X 1 120 X 4 120 X 4 400 X 1 400 X 1 700 X 1 POWER OUTPUT @ 1 . NOT RECOMMENDED NOT RECOMMENDED NOT RECOMMENDED 600 X 1 1150 X 1 POWER OUTPUT @ 4 . BRIDGED 240 X 1 240 X 2 240 X 2 N/A N/A POWER OUTPUT @ 2 . BRIDGED NOT RECOMMENDED NOT RECOMMENDED NOT RECOMMENDED N/A N/A TOTAL HARMONIC DISTORTION .08% .07% .08% .03% .03% S/N RATIO (A WTG) REF 1W AT 4 . 79dB 79dB 79dB 65dB 65dB GAIN RANGE 0.25V - 4.0V 0.25V - 4.0V 0.25V - 4.0V 0.25V - 4.0V 0.25V - 4.0V CROSSOVER RANGE HIGH 55Hz- 250Hz LOW 55Hz - 250Hz HIGH 55Hz- 250Hz LOW 55Hz - 250Hz HIGH 55Hz- 250Hz LOW 55Hz - 250Hz LOW 55Hz - 250Hz LOW 55Hz - 250Hz FREQUENCY RANGE 20Hz - 20KHz 20Hz - 20KHz 20Hz - 20KHz 20Hz - 250Hz 20Hz - 250Hz BASS BOOST Quasi Parametric Bass EQ +15dB @ 40Hz to100Hz 0dB - +15dB @ 45Hz Quasi Parametric Bass EQ +15dB @ 40Hz to100Hz Quasi Parametric Bass EQ +15dB @ 40Hz to100Hz Quasi Parametric Bass EQ +15dB @ 40Hz to100Hz We reserve the right to change individual specifications at FRONT SUB SUB GAIN 55 250 HIGH FULL MIN MAX HIGH 0 15 MIN MAX 55 250 GAIN FRONT BASS BOOST LOW L R POWER/ PROTECT X-OVER 40Hz 100Hz BOOST FREQ PHASE 00 1800 SUB FRONT RIGHT BRIDGED LEFT +12V TURN GND ON FRONT SUB SUB GAIN 55 250 HIGH FULL MIN MAX HIGH 0 15 MIN MAX 55 250 GAIN FRONT BASS BOOST LOW L R POWER/ PROTECT X-OVER 40Hz 100Hz BOOST FREQ PHASE 00 1800 SUB FRONT RIGHT BRIDGED LEFT +12V TURN GND ON 7 8 + - 2 STEREO 4 CHANNEL HIGH PASS With SUBWOOFER Set BASS BOOST as Needed Set this Crossover for HIGH Use this Crossover for LOW Use this Crossover for HIGH XDi803 + - 2 STEREO 2 CHANNEL HIGH PASS With SUBWOOFER Set BASS BOOST as Needed Set this Crossover for HIGH Use this Crossover fo...