Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Listed Five-Year Worry-Free Warranty MOS-FET Output Devices Class-A Full Complementary Front End Modular Construction XLR and 1/4” inputs on "M” Models Barrier Strip and 1/4" Inputs on "C" Models Stereo, Mono & Bridging Modes LED meters on "M" models Forced Air Cooling Perfect Overload and Square Wave Response Stable Into Any Load Self-Protecting Under Virtually All Conditions Specifications POWER OUTPUT EIA SPECIFICATION (±1dB <1% THD 20Hz-20kHz) STEREO (Rated Per Channel) 2 ohms: 675 Watts RMS 4 ohms: 500 Watts RMS 8 ohms: 300 Watts RMS MONO BRIDGED 4 ohms: 1350 Watts RMS 8 ohms: 1000 Watts RMS FTC SPECIFICATION (min power <.01% SMPTE IMD) STEREO (Rated Per Channel) 4 ohms: 400 Watts RMS 8 ohms: 250 Watts RMS MONO BRIDGED 8 ohms: 800 Watts RMS Total Harmonic Distortion: .004% 1kHz, an .01% 20Hz, 8‘ 1 .05% 20Hz-20kHz, 812 IM Distortion (SMPTE): .004% 812 (IHF): .01% 812 Damping Factor: >100 20Hz-20kHz Bandwidth: 100kHz Slew Rate: 50V/|iS Frequency Response: ± .5dB 10Hz-50kHz Rise Time: 2iiS 10%-90% Full Power Input Sensitivity: 1.7 V Hum and Noise: >110dB below full output Power Requirements: 110-125VAC, 50-60HZ Size: 19"L x 5.25"H x 16”D Shipping Weight: r ■ ■ 65 lbs Architect’s Specification Aahly Model 2000M The power amplifier, being of two channels, shall deliver a minimum power of 250 walls per channel Into 8 ohm loads. 400 watts per channel into 4 ohm loads, or 600 watts per channel into 2 ohm loads with both channels operating. When switched into bridged mono mode. It shall deliver at least 500 watts Into a 16 ohm load. 800 watts Into an 8 ohm load, or 1200 watts Into a 4 ohm load. The amplifier shall be Immune to damage from shorted, open, or mismatched loads. The amplifier shall have a gain of 29dB ± .5dB per channel and an input sensitivity of 1.7 Volts ± 2% for full rated output. Frequency response shall be 10Hz to 20kHz t .5dB. It shall be stable Into any load Including pure capacitors and Inductors. Hum and noise shall be at least 1 lOdB below full output and SMITE Intermodulation distortion shall be less than .01% at full output. The amplifier shall have rear panel switching for mono and bridging modes and rear mounted level controls. The Inputs shall be balanced bridging type with male and female XLR type connectors as well as 1 /4" phone Jacks. A three-color LED type Indicator shall be employed to show the power level of each channel and self contained forced air cooling shall be used. The power output devices shall be of the Lateral MOS-FET type. The ampliflcr shall weigh 551b. net and mount In a standard 19 Inch rack using three spaces (5.25' high). The power requirement shall be 110- 125VAC. 50-60Hz The power amplifier shall be an Ashlv FET-2000M. Ashly Model 2000C The power amplifier, being of two channels, shall deliver a minimum power of 250 watts per channel Into 8 ohm loads. 400 watts per channel Into 4 ohm loads, or 600 watts per channel Into 2 ohm loads with both channels operating. When switched Into bridged mono mode, it shall deliver at least 500 watts Into a 16 ohm load. 800 watts Into an 8 ohm load, or 1200 watts Into a 4 ohm load. The amplifier shall be Immune to damage from shorted, open, or mismatched loads. The amplifier shall have a gain of 29dB t .5dB per channel and an Input sensitivity of 1.7 Volts i 2% for full rated output. Frequency response shall be 10Hz to 20kHz ± .5dB. It shall be stable into any load including pure capacitors and inductors. Hum ...
Otros modelos de este manual:El receptor y el amplificador - FET-2000C (1.81 mb)