Votos - 2, Puntuación media: 4 ( )

Fabricar: Philips Tamaño del archivo: 1.84 mb Nombre del archivo: Idioma del manual:

. Refer to the documentation from your service operator on how to insert a smart card into the Conditional Access Module. 1. Switch off the TV. 2. Follow the directions printed on the CAM and insert the CAM into the Common Interface at the side of the TV. 3. Push the CAM in as far as it will go, then wait for the CAM to be activated. This takes a few minutes. To prevent digital services from being deactivated, do not remove the CAM from the slot when it is in use. Watch CAM services 1. After inserting and activating the CAM, press OPTIONS. 2. Select [Common interface], then press OK. 3. Select the CAM provider and press OK. 6 Troubleshooting Contact Philips Warning: Do not attempt to repair the TV yourself. This may cause severe injury, irreparable damage to your TV or void your warranty. If you cannot resolve your problem, refer to the frequently asked questions (FAQs) for this TV at You can also contact Philips Consumer Care in your country for support. You can find the contact number in the leaflet that accompanies the TV. Take a note of your TV model and serial number before you contact Philips. These numbers are printed on the back of the TV and on the packaging. General TV The TV does not switch on: . Disconnect the power cable from the power outlet. Wait for one minute then reconnect it. . Make sure that the power cable is securely connected. . Make sure that the power switch at the base or back of the TV is switched on. The TV does not respond to remote control or front controls when switched on The TV requires some time to start up. During this time, the TV does not respond to the remote control or front controls. This is normal behavior. The standby light on the TV blinks red: Disconnect the power cable from the power outlet. Wait until the TV cools down before you reconnect the power cable. If the blinking reoccurs, contact Philips Consumer Care. You forgot the code to unlock the child lock feature: Enter ‘8888’. The TV menu is in the wrong language: Change the TV menu to your preferred language. For more information, see Set up your TV > Menu language (Page 40). When you are turning the TV on, off or to standby, you hear a creaking sound from the TV chassis: No action is required. The creaking sound is due to the normal expansion and contraction of the TV as it cools and warms up. This does not affect performance. When the TV is in standby, a startup splash screen is displayed, then returns to standby mode: This is normal behavior. When the TV is disconnected and reconnected to the power supply, the startup screen is displayed at the next startup. To switch on the TV from standby, press on the remote control or press any key on the front of the TV. TV channel Previously installed channels do not appear in the channel list: Make sure that the correct channel list is selected. No digital channels were found during the installation: . Make sure that the TV supports DVB-T, DVB-C or DVB-S in your country. . Make sure that the antenna is properly connected and the correct network is selected. Picture The TV is on, but there is no picture or the picture is distorted: . Make sure that the antenna is properly connected to the TV. . Make sure that the correct device is selected as the display source. . Make sure that the external device or source is properly connected. There is sound but no picture: Make sure that the picture settings are set correctly. There is poor TV reception from an antenna connection: . Make sure that the antenna is properly connected to the TV. . Loud speakers, unearthed audio devices, neon lights, high buildings and other large objects can influence reception quality. If possible, try to improve the reception quality by changing the antenna direction or moving devices away from the TV. . If reception on only one channel is poor, fine-tune this channel. There is poor picture quality from connected devices: . Make sure that the devices are connected properly. . Make sure that the picture settings are set correctly. The TV did not save your picture settings: Make sure that the TV location is set to Home. You can change and save settings in this mode. The picture does not fit the screen; it is too big or too small: Try a different picture format. The picture position is incorrect: Picture signals from some devices may not fit the screen correctly. Check the signal output of the device. The picture from broadcasts is scrambled: You may need a Conditional Access Module to access content. Check with your service operator. An "e-sticker" banner displaying information appears on the TV display: The TV is in [Shop] mode. To remove the e-sticker, set the TV to [Home] mode, then restart the TV. Position the TV > Location (Page 9). The computer display on the TV is not stable: . Make sure that your PC uses the supported resolution and refresh rate. See Product specifications > Display resolutions (Page 61). . Set the TV picture format to [Unscaled]. Sound There is a pi...

Descargar ahora

Introduzca dos números de la imagen: