Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
To receive lower frequency, press the DOWN button. To receive higher frequency, press the UP button. 0 TUNING MODE button Used to select the tuning mode between AUTO and MAN'L. © FUNCTION button Press this button to select the reception band between FM, AM and LW. © MEMORY button When this button is pressed, the MEMO indicator flickers in the display for about 5 seconds. During this period, press the desired preset station button to store the displayed frequency. @ P1-P8/P9-P16 button Press this button to change the range of the preset station buttons. When this button is pressed, the selected range of the P1-P8/P9-P16 indicators flickers for about 5 seconds. 0.3'£FU'\7.iiV-. B AUTO TUNING If signals are strong and there Is no interference, quick automatic search tuning is possible. 1. Select the reception band with FUNCTION button 2. Press the TUNING MODE button so that the AUTO indicator lights up. 3. Use the TUNING button to tune. The tuning will start automatically and stops at broadcast station frequency with a sufficient signal strength. 4. If the station where tuning stops is not the one you want, press the TUNING button once again. II MANUAL TUNING Auto tuning may be impossible if the station signal is weak. If so, use manual tuning. 1. Select the reception band with FUNCTION button. 2. Press the TUNING MODE button so that the AUTO indicator goes off. 3. Use the TUNING button to tune. The frequency will change rapidly if the TUNING button is kept pressed. Release it slightly before reaching the desired frequency, and then press it intermittently until the desired frequency is reached. H PRESET TUNING The preset station button can be used to select, at a single touch, any desired station which has been preset. 1. Tune to the desired station using auto or manual tuning mode. 2. Select the range of the preset station button with the P1-P8/P9-P16 button. 3. Press the MEMORY button and then while the MEMO indicator is flickering, press the desired preset station button. 4. To receive the preset station, select the range of the preset station with the P1-P8/P9-P16 button and press the desired preset station button. ® Follow the same procedure for other preset station buttons. The new setting will be programmed in place of the former one. • Memory back-up The memory back-up circuit will prevent the programmed information from being lost even though the power Is switched OFF for timer use of other temporary power failure. If, however, the unit is not used for a long time, the memory may be erased. If so, it can be re-programmed by simply following the original procedure. 7 TFOJBlSSi-IC&rfMvi When your unit fails to function properly, before assuming It is faulty, check it according to the following troubleshooting list. It details the corrective action you can take yourself without hav:ng to call a service engineer. If you have any doubts or questions, get in touch with your nearest YAMAHA dealer. SYM?Tf:iw REMEDY FM Crackling sounds from time to time (especially in weak signal areas). « Ignition noise from passing vehicles. • The FM antenna should be put up as high as possible, away from the road, and a coaxial cable used. • Noise from thermostats or other electrical equipment ® Attach a noise suppressor to the equipment causinq the noise FM stereo reception is noisy. • Because of the characteristics of FM stereo broadcasts, this Is limited to cases where the transmitter is far away or the antenna Input is poor. • Check the antenna connections. • Try using a multiple element FM antenna. ® Set the TUNING MODE button to MAN’L mode. The STEREO indicator flickers and reception is noisy. ® Insufficient antenna input. ® Use an antenna appropriate for the reception condition in your area. ® Not tuned correctly. • Tune again. There is distortion and clear reception cannot be obtained even with a good FM antenna. ® There is multipath interference. • Adjust antenna placement to eliminate multipath interference. No stereo effect even with a stereo broadcast. • The TUNING MODE button is set to MAN’L. @ Set the button properly. A desired station cannot be tuned in with Auto tuning. ® The station is too weak. ® Use Manual tuning mode. • Use high quality directional FM antenna. Previously preset stations can no longer be tuned in. ® The tuner has been unplugged for a long period. ® Repeat the presetting procedure. AM Insufficient sensitivity. ® Weak signal or loose antenna connections. ® Tighten the AM bar antenna connections and rotate it for best reception. A desired station cannot be tuned in with Auto tuning. • Use Manual tuning mode. There are continuous crackling and hissing noises. • These noises result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. ® Use an outdoor antenna and a ground wire. This will help some what but it is difficult to eliminate all noise. There are buzzing and whining noises (especially in ...